Jump to content
SAU Community

Recommended Posts

Some parts i no longer need

1. Trust/Greddy Cam Shafts 272 9.15 Lift RB26 $400

2. AEM iginition Module $250

3. Ems Stinger V4 4424 Engine Management Latest comes with loom to suit Rb26 $600

4. Bosch 1600cc Injectors Indy Whites x 6 Brand new still in box $700 for the set

5. Sard 1000cc Injectors x 6 $500 for the set

Link to comment
https://www.sau.com.au/forums/topic/318291-few-performance-parts/
Share on other sites

Hey,

Would the sard injectors fit on stock fuel rail?

And does it come with O rings?

I'm assuming these parts is for RB26 correct?

Where you located at?

Cheers

Grant

  • 2 weeks later...

Hey man ecu still for sale??? Whats the barcode numbers on the bottomside of the computer? And where you at?

Some parts i no longer need

1. Trust/Greddy Cam Shafts 272 9.15 Lift RB26 $400

2. AEM iginition Module $250

3. Ems Stinger V4 4424 Engine Management Latest comes with loom to suit Rb26 $600

4. Bosch 1600cc Injectors Indy Whites x 6 Brand new still in box $700 for the set

5. Sard 1000cc Injectors x 6 $500 for the set

  • 1 month later...
Some parts i no longer need

1. Trust/Greddy Cam Shafts 272 9.15 Lift RB26 $400

2. AEM iginition Module $250

3. Ems Stinger V4 4424 Engine Management Latest comes with loom to suit Rb26 $600

4. Bosch 1600cc Injectors Indy Whites x 6 Brand new still in box $700 for the set

5. Sard 1000cc Injectors x 6 $500 for the set

is ems still for sale?

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...