Jump to content
SAU Community

Recommended Posts

Heya!

I am about to do an R33 brake conversion and Ichiba 5-stup upgrade on all four corners of my ABS equipped Cefiro.

I would prefer to remove the whole ABS system to reduce weight, increase engine bay space and just generally tidy up excessive line etc.

What is the correct way to do this?

Or do I just leave it alone all together?

Link to comment
https://www.sau.com.au/forums/topic/319753-abs-removal-how-to/
Share on other sites

Even for track use, ABS can be very helpful, and its easy to disable (fuse).

If you must remove it, pull the globe from the dash, disconnect the loom under the rear shelf and remove the ABS computer, remove all the brake lines, ABS hub, sensors, etc.

Keep in mind the hard lines on Cefiro are Cefiro only...as they're a mix of using S13 master cylinder (which will also need to be replaced) running along an R32 firewall. Making your own solid brake lines isnt hard, if you're doing the R33 conversion you'll need to make up your own flexible brake hoses too (or dodgey modify the banjo bolt), so just do them all in one hit, but yeah, I reckon keep it...more con's than pro's if you remove it.

Even for track use, ABS can be very helpful, and its easy to disable (fuse).

If you must remove it, pull the globe from the dash, disconnect the loom under the rear shelf and remove the ABS computer, remove all the brake lines, ABS hub, sensors, etc.

Keep in mind the hard lines on Cefiro are Cefiro only...as they're a mix of using S13 master cylinder (which will also need to be replaced) running along an R32 firewall. Making your own solid brake lines isnt hard, if you're doing the R33 conversion you'll need to make up your own flexible brake hoses too (or dodgey modify the banjo bolt), so just do them all in one hit, but yeah, I reckon keep it...more con's than pro's if you remove it.

Do you have it?

Its seems to be a rather shitty system or mybe mine is faulty?

When i hit bumps on the road while braking the ABS has a tendency to kick in and then off again making it quite annoying. This happens when under braking and the driven wheel(s) skip off the ground when on a bumpy surface, causing a bit of slip in the diff or something and (i assume) the ABS computer reads this as high speed or hard braking braking and jumps into action when i dont want it to.

I like to be in full control of my cars functions but the ABS seems do have a bit of a mind of its own at times.

I have all the gear to do the conversion including braided lines etc.

I have also just been informed that there may be some legalities involved if i remove this. Is this the case?

If I keep the abs will it work with the hubs and calipers i have?

Or do I need ABS compatible hubs or something?

While on this toppic,

What the difference with the ABS diff? I have been told its longer but will this affect my decision to put a shimmed, 4.11:1 R33 center in it?

Not sure on legalities, read the Australian Design Rules.

I've yet to give my ABS a work out in the Ceffy but it has been usefull in my 94 J30 Maxima. I can't relate the symptoms you described to any ABS Nissan I've driven, might just be yours? Cefiro's had that supersonic suspension setup from the factory that had (auto) adjustable damper rates...the ABS might be tied in with this.

I've never taken a look at how the ABS sensor at each wheel works...you should be able to use the same knuckle and wheel hub though.

Like I said, you can just pull the ABS fuse if you like, for times when you don't want it interfering if it is doing so, and then put the fuse back in for driving around on the street?

The extra weight isnt that much, and can be a lifesaver in the wet/limited traction situations.

Not sure on legalities, read the Australian Design Rules.

I've yet to give my ABS a work out in the Ceffy but it has been usefull in my 94 J30 Maxima. I can't relate the symptoms you described to any ABS Nissan I've driven, might just be yours? Cefiro's had that supersonic suspension setup from the factory that had (auto) adjustable damper rates...the ABS might be tied in with this.

I've never taken a look at how the ABS sensor at each wheel works...you should be able to use the same knuckle and wheel hub though.

Like I said, you can just pull the ABS fuse if you like, for times when you don't want it interfering if it is doing so, and then put the fuse back in for driving around on the street?

The extra weight isnt that much, and can be a lifesaver in the wet/limited traction situations.

Sweet as, i think i'll just leave it alone and as you said, take out the fuse if im on track or somthing.

At the end of the day my intention with the ceffy is for a streeter so probably best left as is.

The only other thing that bothers me is that the ABS unit sits right above the turbo/dump and when hard driving is applied i tend to lose a bit of stopping power, i would say, from the brake fluid being overheated. I have a makeshift heatshield in place, which seems to work ok but maybe a more permanent shield is needed if i'm to keep the system.

on a side note

I use tein HA coilovers that came fitted on the car from japan

Highmount turbo? Either way it's a good point, heat right next to brake fluid is not cool. It's also next to your power steering resevoir as well :blush:

http://www.7tune.com/newtune/justin/cefiro/5.jpg

(more on that drifter, here)

More permanent heatshield and opening an air duct into that corner would help.

If you're making your own solid lines, you could drill some holes into the firewall and run them back in there, under that gutter/drain,

yeah nice pic. I was there at setonai circuit with justin and laurence. we were there for msc event. even got a pic with orido as he was there judging...

...anyway back on topic :blush:

my reason for removing initially was because the unit was leaking... brake fluid leak is terrible for paint/metal... still happy it's gone though.

Keep in mind the hard lines on Cefiro are Cefiro only...as they're a mix of using S13 master cylinder (which will also need to be replaced) running along an R32 firewall.

S13 master cylinder is the same shape as the R32 master cylinder. Therefore the hard lines should be identical to the R32.

Dunno now, but thinking about it the strut towers/wheel arches are going to be the same shape as the S13, so the R32 lines probably wouldn't fit. Not sure how different the firewalls are, but the master cylinders are the same shape (S13/R32).

Hard lines don't really go by strut towers or wheel arches though.

Firewall (according to parts thread) is same as R32)...they run along the firewall then drop down to the chassis rail and then breach the wheel arch, the rears go down the firewall and run along the inside of the right chassis rail, then seperate when they reach the cradle.

Strut towers are wheel arches are closer together than S13....AWD Cefiro's can probably get away with R32 solid lines, to say the least.

Wonder if anyone has done it ? I need to make some new ones up for mine, was just going to use the old bolts, some tube and get a tube bender.

  • 2 weeks later...

I have just removed my ABS completely and replace it with R32 brake master and booster and used the line from the front half of a R32 shell a mate was going to throw out.

You need to replace the master cylinder because ABS masater has two line coming out going to the ABS and then the ABS distributes to all four calapers. Non ABS units have three lines coming out, one to front left, one to front right and one to rear for both sides.

R32 solid lines will fit but a few man handling bends will be needed, but they all fit up on the fronts.

The rear all you have the do is get the shortest of the solid lines, undo the line that goes to the rear at the little junction box just under the brake booster and contect it to the brake master.

Bleed as you normally would but a few more time then normal to get all the air out and brakes will be better then ever.

I will try take some pics and get a list of things required for the change out

But see attached pic of a non ABS brake master.

Billy

post-5013-1274855822_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...