Jump to content
SAU Community

Recommended Posts

has anyone ever opend their bonnet after driving in rain? especially heavy rain? everything is soaking wet, the vents will be fine no water will get anywhere.

most people hose their engine bay down to clean it, i do most times i wash the car, its fine

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

just excessively spray ALL the electrical wires and connectors etc with WD40 or some other type of water dispersant

then degrease the shit outta it, then hose it all off

make sure engine is warm when you do it

then go for a 15min drive

and if need be spray electricals with WD40 again

As for CF bonnets,

i wouldnt buy one with a forward facing vent personally, not unless it had a mesh/filter or something

vents that face the driver are the best, wind is streamlined across the bonnet going over the vent, and creating a vacuum thus sucking out hot air from the engine

Yesterday was the first time the weather got the better of my bonnet but it came up on top like mentioned previously the bonnet are designed to overcome weather conditions .As for the bonnet being illegal yeah they have been illegal from dot. But most police will get out the book if they really want to come down on you . I drive mine most days and haven’t had much trouble at all that doesn’t go to say I never will, but I think it comes down too you doing stoopid things in certain places to attract the wrong attention police or otherwise. So with that in mind I would be careful in what you do and where you go if you want something more unique then conventional.

what i meant was it was the first time i really put my put bonnet against the elements it hasnt rained since iv had it on the car but the other day i had to take it out and it rained , youll be happy to know it didnt melt

I have been thinking about getting my bonnet modified with some cold air vents and have been worried about the water thing too.

I want to get a vent right on top of the pod.

Dont know exactly how yet but I am going to get something on the underside of the bonnet that will allow me to shut off the vent in wet weather.

  • 2 weeks later...
Well just after having the cf bonnet on for a few weeks, I got defected. No fines, just to have it cleared.

that has to suck :P , your probably the first i know that got done for cfb just out of curiosity where you from ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...