Jump to content
SAU Community

Recommended Posts

Hi Guys.

What a fab. forum SAU must be proud and I think you should be.

I have been looking for a new vehicle mainly because I have to cart around a motor wheelchair, I have been looking at the ElGrand on line , but I now have seen online a Stagea wagon and it appeals to me ,But I cannot find enough info or brochers so this is where I hope you guys can help. I am looking at a 2002 AR-X four NM35.

first: I need to know what is the size of the rear opening from floor to roof , wheelchair stands about 1mt.

.....: where can I get a brocher " in english " of the NM35.

......: I'm confused about the different models in this range.

......: as the chair weights about 140Kg. would I need to change the rear suspension or can it cope as is.

......: do these vehicles have cruse control , and do I have to change the radio and gps to english.

......: Is there much difference between the Stagea and mitsubishi Legnum I have had both brands ie:Nissan and Mitsubishi, and never had a problem with either.

I did sent the same request earlier today but it seems to have got lost.

OK,this will do for now

thank you for your time this is a bit long winded,,,

Link to comment
https://www.sau.com.au/forums/topic/324588-need-help-on-stagea/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...