Jump to content
SAU Community

Recommended Posts

Hi there Guys,

It's been a while since i have posted a question and i have done some searching through the forums but i can't seem to find what i'm looking for.

Problem -

1995 Series 1.5 Skyline RB25DET

* Issues started with low idle - and engine stalling when cold (By the way it's an automatic) Engine would stall if any load was put on it.

* Investigated timing and all timing marks line up for 15Deg

* I've had fun by doing the following - re-Gapped sparkplugs; Got a 2nd hand CAS; Got a 2nd hand AFM; Brought new plugs

I've just been playing with the car today and managed to get it firing by itself but i had to hold my hand over the AFM to restrict the flow Engine was able to idle for 3-5secs before stalling again - I repeated the process and when firing took my hand off and died -

I'm thinking in my mind the following -=-

Either I have a break in the pipe work (Intake) but when i had my hand over the AFM the pipe was sucking in and i couldn't hear any other air. Or the AFM is cactus.

Does anyone have any other thoughts -

Regards,

Ashley Neal.

Link to comment
https://www.sau.com.au/forums/topic/324689-r33-rb25det-15-dramas/
Share on other sites

Check trouble codes then

check fuel pressure

The ECU did show me Code 55 - Everything OK -

The Fuel Pump is working - I disconnected the Feeder pipe and put into a bottle plenty of fuel went into the bottle - Is there a spec on how much presure should be there?

whats it like when its warm?

is it on a stock ecu?

if its always idling very low and is on a stock ecu, perhaps try to adjust the idle up a touch. theres also a mixture screw on the back of the ecu that you could fatten up a touch, that makes them run a little easier when their cold. But if you add fuel on base idle you will also want to up the idle screw.

GL

whats it like when its warm?

is it on a stock ecu?

if its always idling very low and is on a stock ecu, perhaps try to adjust the idle up a touch. theres also a mixture screw on the back of the ecu that you could fatten up a touch, that makes them run a little easier when their cold. But if you add fuel on base idle you will also want to up the idle screw.

GL

Hi mate,

The car seems to be racing when warm - sitting just shy of 1000rpm - when spec say's 650+/- has a slight sputter every now and again.

The ECU is a completely sealed unit with no trimpod for adjustment. I also checked for Dry-Solder in the AFM - and everything checks out there = ECU still giving Codee 55 = All Ok.

Edited by Nissan Maaaart
id go for fuel pump.

They can throw up an array of symptoms but seem ok with prelim testing like you did.

Otherwise vacuum leak...

Thanks mate, I've checked all the Intake piping and there is no apparent air leaks - does anyone know what type of presure should be coming from the rail --

I also did some further testing and with doing the following - blocking the Intake - and allowing a small vaccum of air into the AFM - the car would start with timing retarded - engine would fire on it's own for a moment - but if i removed my hand or made the vaccum less the engine would stall --

The suction from cranking felt quiet faint - can anyone comment on this?

Thanks.

did you look at all the piping cooler etc? my freind had a problem with his for 3 weeks before finding a pin hole in the intercooler.

try changing the fuel filter as well my turbo pulsar wouldnt run and idle and it was a blocked fuel filter but it still primed etc

+1 for fuel filter...im assuming you've checked your air filter..

My mates car wasnt starting, and racing at idle, i blew out the air filter with a compressor and it ran great for another couple of days..cheap prick wouldnt spend 20$ on a new one

Righto - Still Not anywhere -

I've replaced - all clamps, enusres tight- checked Cooler for leaks - new fuel filter -

And still no go - does anyone know how much New AFM's are and where to get them -- as I got a price from a crowd and it seemed a little steep at 780$ex out of Melb.

Or does anyone on the Northside of Bris have a 3 pin (Pink Lable) AFM that is known good that i could try?

Thanks.

Try a diffrent AFM had a simular problem on a mates car, Go to a wreckers or something and you might be able to test it, also AAC valve is clean? check that as well. Do you also have a BOV? or is it stock standard?

Edited by geraus

just unplug the AFM and see if it idles

the engine will run with no AFM and should idle OK, but it wont drive very well and will rev cap at 2500RPM

if the AFM is the culprit when you unplug it, it should run to normal idle

if the AFM is NOT the culprit when you unplug it, the same problem will be present and it will stall

just unplug the AFM and see if it idles

the engine will run with no AFM and should idle OK, but it wont drive very well and will rev cap at 2500RPM

if the AFM is the culprit when you unplug it, it should run to normal idle

if the AFM is NOT the culprit when you unplug it, the same problem will be present and it will stall

Hi buddy,

The vehicle wont even start - or run enough to test this theory.

I'll try the fuel line thing shortly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...