Jump to content
SAU Community

Recommended Posts

Hi All,

I was driving my R33 home from work today and noticed when accelerating from 80 - 100 in 5th under heavy load there was a chatter coming from the engine bay somewhere. Not too sure what it is but I did notice that my A/F ratio is running pretty rich (13 - 13.5)

I took off the pod recently and put back the stock airbox however I think the SAFC was tuned with the pod on.

Any thoughts on what the sound might be?

Link to comment
https://www.sau.com.au/forums/topic/325312-chatter-noise-under-load/
Share on other sites

14.7 is stoich, but you only use that for cruise. when it comes to putting load on in a turbo car then you want things to be 12 or less (anything higher than about 12.5 at high boost and rpm is going to have a short life), however at 80 to 120kmh in 5th gear you are pretty low in the revs so 13.5 probably wouldn't be too far off the mark.

what did the noise actually sound like? was is like a marble in a tin can? if so then that is most likely pinging, which is bad. however if it starts doing it more often in other gears and rev ranges then you may have a broken manifold stud and the sound is the gasket vibrating.

if the sound was more like it was misfiring then it's either your coils or spark plugs

It may be pinging as Marc said. If so, you can top up your fuel with extra toluene (methylbenzene) just to check.

Alternatively, octane booster can be used; but 1x bottle will make little difference. 2x bottles are needed to check.

If pinging ceases, then your state of tune will need to be rectified.

thanks for the replies guys,

when driving home on some nice road it didn't really sound like marbles in a can. oddly enough the only sort of sound I can compare it to was two pieces of paper hitting each other really quickly. It also isn't a constant noise.

Ill put some octane booster in over the weekend to see if it helps.

Might also go through the engine bay to see if anything is loose.

  • 2 weeks later...

Well I finally got one of the NVH guys at work out over lunch to listen to the chatter.

Found out that the sound of coming from the gearbox/gear stick.

When I am accelerating in 5th gear and push the gear stick up and to the left the chatter sound becomes worse but when the gear stick is pulled slightly downward it goes away.

We were thinking it may be gear boot related. Has anyone else had this issue before?

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...