Jump to content
SAU Community

Recommended Posts

I have been tossing between a Stagea and a Legnum for ages now. I think I have come to the conclusion that a C34 Stagea is the car I want.

I just wouldn't mind some feedback from Stag enthusiasts to help me lock in my decision.

Firstly, I have my eye on an RS-V. I have been told that an RS-V is about 100kg lighter than an RS-4. Therefore, I am thinking that an RS-V will be quicker off the line than a heavier RS-4.

Also as an RS-V is approximately 100kg lighter than a RS-4, does this mean that performance wise, an RS-V will be nearly as responsive as a Legnum? I have read that Legnums are much more responsive than a Stag but I am assuming this comparison is with a RS-4.

How much more fuel efficient is an RS-V?

The car I am keen on is fitted with an Auto trans, so I will eventually get some work done to get a shift kit fitted. Improve more responsiveness down low.

Finally, I am not sure whether I should definitely go with a rear wheel compared to a 4 wheel drive Stag. I am not going to use this vehicle as a Drifter nor do I really need the traction of a 4 wheel drive system. Can anyone give me a reason why you have chosen a RWD or AWD?

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/
Share on other sites

I believe the stock C34 will not be as quick as a Legnum - its bigger and heavier.

My first Stagea was a n/a neo 2wd - a nice car but my current awd is so much better in the twisty/wet conditions - the Atessa distributes power front to rear according to need and with a little more (or a lot more) horsepower you really appreciate the way it gets the power down.

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5312144
Share on other sites

I believe the stock C34 will not be as quick as a Legnum - its bigger and heavier.

My first Stagea was a n/a neo 2wd - a nice car but my current awd is so much better in the twisty/wet conditions - the Atessa distributes power front to rear according to need and with a little more (or a lot more) horsepower you really appreciate the way it gets the power down.

Thanks for the feedback mate. I understand that a C34 will be slower than the Legnum but was just curious as to how a rear wheel powered C34 will measure up againts a Legnum. I think there is 100kg difference between a RS-4 and Legnum, therfore without the Stags Altessa gear (which I believes is about 100kg) both vehicles will be on par in terms of kerb weight.

I also believe that a Legnum's twin snail set up will help with responsiveness over a RS-V/RS-4.

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5312308
Share on other sites

Greenghost has a RSV, and when we tested it against my auto Legnum, I was comprehensively flogged.

That said, why not get a RS4S? That way, you get manual, and it gives you the option of converting to RWD down the track, if you really insist.

As far as not needing AWD, take a RS4 stagea for a drive in the wet, and see how you feel... :miner:

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5312675
Share on other sites

Firstly, I have my eye on an RS-V. I have been told that an RS-V is about 100kg lighter than an RS-4. Therefore, I am thinking that an RS-V will be quicker off the line than a heaver RS-4

Minus the fact it will not be gertting full traction when you tromp it off the line.

Attessa FTW

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5312792
Share on other sites

I have a S2 RS4.

I think id prefer a RWD.

Less maintenance hassels down the track, when 4WD is turned on its a bit notchy steering when parking etc, RWD has less weight too.

I did my first hard launch the other day with 4WD with mode on (normally just go around in RWD). Got airborne I think it has alot more go then in RWD mode.

The Stageas probably a lot easier to modify then a Legnum. If your after big power you could go for the R260 model.

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5313205
Share on other sites

I have a S2 RS4.

I think id prefer a RWD.

Less maintenance hassels down the track, when 4WD is turned on its a bit notchy steering when parking etc, RWD has less weight too.

I did my first hard launch the other day with 4WD with mode on (normally just go around in RWD). Got airborne I think it has alot more go then in RWD mode.

The Stageas probably a lot easier to modify then a Legnum. If your after big power you could go for the R260 model.

"normally just go round in RWD"???!!!

AWD is always on unless you have removed the front driveshaft and pulled the fuse. The Attessa computer allocates drive according to need - normally 95% rear but up to 50/50 according to the conditions.

Steering is not affected. If you think it gets notchy when you turn the synchro button on that's because the synchro button locks it into 50/50 mode for pulling the car out of a wet paddock etc. That is not the "4wd" button.

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5313237
Share on other sites

I have a S2 RS4.

I think id prefer a RWD.

Less maintenance hassels down the track, when 4WD is turned on its a bit notchy steering when parking etc, RWD has less weight too.

I did my first hard launch the other day with 4WD with mode on (normally just go around in RWD). Got airborne I think it has alot more go then in RWD mode.

The Stageas probably a lot easier to modify then a Legnum. If your after big power you could go for the R260 model.

I think you've been smoking more than tyres!

You can't turn off the AWD system in a Stagea! If you pull the fuse on it (under the bonnet Son), you are liable to screw up your clutch packs in the wheels.

Why anyone would want a big heavy wagon that is available in 4wd, as a RWD is beyond me.... if you want to draw lines up the road buy a V8 Commodore wagon. Cost less, and much more bogan like.

If you wan't a fine wagon, with unparalleled handling, go Stagea AWD it's awesome!

If you've been pressing the button on the dash with the "S" on it, and thinking that this turns the 4WD on, it doesn't. That button is for locking up the AWD, for very slippery surfaces. Don't use it on bitumen. It locks the split to 50% front 50% rear. Read up on the system so that you understand it.

Oh yeah, if you want the full spec sheet PM me your email address I'll send it on.... you'll be shocked! And probably even more confuddled!

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5313253
Share on other sites

Another factor is that if you go for an AWD version, a majority of your suspension problems have already been worked out simply because of the fact that they're more common, so all that research has already been done and plenty of solutions are out there!

I'm not saying that a RWD only model will rule out any mods to suspension, but you will *possibly* need more time to research what goes where and what parts are interchangeable with other Nissan models.

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5313455
Share on other sites

I would say it would depend what kind of fun you want to have when you're going round a corner ;-)

I have a RWD and the only downfall is that suspension parts are harder to come by.

I used to have a wrx wagon, but I decided to go RWD with the Stag. Now I can have a little slideways fun in the wet, and if I wanna take it easy I just put the traction controll back on. Having a clutch would be great though, I'm now considering the manual conversion. :P

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5313573
Share on other sites

"normally just go round in RWD"???!!!

AWD is always on unless you have removed the front driveshaft and pulled the fuse. The Attessa computer allocates drive according to need - normally 95% rear but up to 50/50 according to the conditions.

Steering is not affected. If you think it gets notchy when you turn the synchro button on that's because the synchro button locks it into 50/50 mode for pulling the car out of a wet paddock etc. That is not the "4wd" button.

Yeah I don't know mine has a button below the dash. When thats pressed turn the ignition on and a 4wd lights up on the dash. Then notchy steering etc.

One note: I'd never own a RWD without an LSD.

Edited by QLDR31
Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5313764
Share on other sites

Yeah I don't know mine has a button below the dash. When thats pressed turn the ignition on and a 4wd lights up on the dash. Then notchy steering etc.

Hmm, one of these 2 things could be happening;

A) The light that actually says '4WD' is on and stays on. = Bad. Means your ATTESSA isn't working!

B) The light that has your drivetrain layout, front wheels turning and there is an 'S' in the middle. Hard to explain and I have been trying to work out how to draw it using buttons on my keyboard, but it isn't working! = Normal. 50/50 Synchro is activated. Only use on slippery surfaces as said in previous posts!

Link to comment
https://www.sau.com.au/forums/topic/326259-which-stagea/#findComment-5318522
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...