Jump to content
SAU Community

Recommended Posts

Hi guys, recently had a R34 GT-V skyline go in for inspection in anticipation to buying.

Came back with positive results, thought i'd share them:

r34results.jpg

Uploaded with ImageShack.us

r34results2.jpg

Uploaded with ImageShack.us

Just a question concerning Steering Rack, it is noted that free play is evident.

Also steering pull tends to drift to the left.

How would I go about fixing these problems?

Any comments are appreciated, extremely excited about the car

Link to comment
https://www.sau.com.au/forums/topic/326791-r34-skyline-inspection-report/
Share on other sites

check and ask a mechanic

they sound like basic normal issues to me and most related to wear and tear

i mean some of the reports you get pick up every bloody single issue

and dont focus on the basics, ie engine compression, engine health, and pick out little things like dirty caps etc when more important things could be checked

I've heard there are many other checks that is better than the RACV one. State Roads is one of them.

Also, wouldn't be a bad idea to take it to a mechanic that knows lots about imports, especially Skylines.

use it as a baseline and ask a mechanic workshop (print out the list) to check over them

when i had my ECR33 checked it had 2 pages of little shit and issues

the car had 58,000 on the clock and still going strong with 223,000

so check the specific detail of each item and clarify what they mean

from your report the brake pad issue and keyless entry stand out

the rest seem normal. i mean what 1999 car that is 2nd hand isnt going to have some level of scratches, minor wear/tear and refinishing evidence

An RACV test is not worth wiping your arse with.....i wish people would stop giving money to those (unts

Oh I see what you did there :blush:

When it comes to anything more complex than a Falcon or Commodore I can only echo your sentiments. I have only heard good things about state roads and it seems $500 is a small amount of money to part with to avoid years of pain and thousands of dollars in potentional repairs.

Oh I see what you did there ;)

When it comes to anything more complex than a Falcon or Commodore I can only echo your sentiments. I have only heard good things about state roads and it seems $500 is a small amount of money to part with to avoid years of pain and thousands of dollars in potentional repairs.

I don't think it's $500..... In the other thread, people have stated $250-350 :D

An RACV test is not worth wiping your arse with.....i wish people would stop giving money to those (unts

+1 for the above

I had a stateroads inspection done on the wifes car before purchase....can't remember the exact amount but wasn't over $250. Very happy with the detailed inspection and would highly recommend.

Stateroads is excellent. My mate had an R34 looked at and not only did the guy know everything about cars (obviously), but Skyline specific too. He could tell that the gearbox had been poorly rebuilt and that it was missing some factory seal (can't remember what it was).

Hey guys so i've considered everything and am going to go ahead and purchase the vehicle.

Where would I take it to clear up the problems now and possibly in the future?

SE suburbs btw

Edited by MaddehZ
When it comes to anything more complex than a Falcon or Commodore I can only echo your sentiments. I have only heard good things about state roads and it seems $500 is a small amount of money to part with to avoid years of pain and thousands of dollars in potentional repairs.
I had a stateroads inspection done on the wifes car before purchase....can't remember the exact amount but wasn't over $250. Very happy with the detailed inspection and would highly recommend.
Stateroads is excellent. My mate had an R34 looked at and not only did the guy know everything about cars (obviously), but Skyline specific too. He could tell that the gearbox had been poorly rebuilt and that it was missing some factory seal (can't remember what it was).

+1 for http://www.stateroads.com.au/ , I got my R34 GTT inspected by them before buying it a month or two ago. It's not cheap though at $289 for the comprehensive inspection but you will know heaps more about what you're buying. I also got a quick second opinion by the workshop that did the roadworthy and then took it to Chasers to address one tricky issue.

MaddehZ your RACV inspection report doesn't look too bad provided that the inspector wasn't completely clueless, IMHO. Have a look at the Local Wreckers And Workshops thread for a knowledgeable workshop near you to get that stuff sorted.

The car is from power road, and no the racv check was kind of the decider for me as to whether it was a go-er. Wise choice ?

I've heard good and bad from them and I've been there a few times for myself or for friends. But I still reckon RACV shouldn't be the decider, but a proper mechanic. That's my very honest opinion :cool:

If you are spending that much money on a car, you might as well do everything within your budget to make sure everything is okay, instead of buying it then realise it's a lemon :rolleyes:

steering play in a skyline is usually basic stuff (quite common), non issue really, even if worse case it was bounced off a gutter and the rack was US then your only up for a max of $500 fitted anyway. Id say rack mount bushes or tie rods are slightly worn.

To the people saying it's not a thorough inspection based on this fault report...seems to me they've only listed what is wrong with the car (the important part) and not what is fine with it. If it's a well kept car then the fault report isn't going to be very extensive. I'm sure the actual inspection had a hundred more variables to check for than what they listed on the faults report. I guess they could have been more specific with the source/cause of the problem and a possible fix for it but that's your mechanic's job.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...