Jump to content
SAU Community

Recommended Posts

hey all,

my v36 sedan is currently at the compliance workshop so it won't be long now - yay!

in the mean time, i am trying to organise some new rims. it's a my2007 type sp so the stock rims are 18x7.5 (FR) and 18x8.5 (RR). my questions are:

- any ideas what i could go comfortably up to?

- will 20s be too large? are tyres easility available?

- how wide can i go?

- will i need different widths to match? eg 8.5 fronts and 9.5 rears

any help would be appreciated. actual experience would be even better.

thanks for reading.

...sykryd

Link to comment
https://www.sau.com.au/forums/topic/326927-wheels-for-v36-sedan/
Share on other sites

20's are fine. Yes they are easily available.

i went for a 20X9.5 +15 front 20X10.5 +18 rear on my coupe, which is *very* aggressive offset.

widths, sizing, and offset is all dependant on how you want the car to sit.

IMO the "stance" (offset & widths) is just as important as actual wheel design choice.

check out http://www.rimtuck.com and searching for a infiniti g37 sedan for some sizing / pics.

Edited by loz-tuned

thanks for the link. thats a great looking website. i couldn't find anything under g37 sedan, but i did find a couple of 19s under g35 sedan.

your set up must look awesome. i can't believe how wide you've gone - 2inches over (my) stock!! i'd love to see some pics if you have them. also, do you have a (4 door) sedan or the coupe?

  • 1 month later...
hey all,

my v36 sedan is currently at the compliance workshop so it won't be long now - yay!

in the mean time, i am trying to organise some new rims. it's a my2007 type sp so the stock rims are 18x7.5 (FR) and 18x8.5 (RR). my questions are:

- any ideas what i could go comfortably up to?

- will 20s be too large? are tyres easility available?

- how wide can i go?

- will i need different widths to match? eg 8.5 fronts and 9.5 rears

any help would be appreciated. actual experience would be even better.

thanks for reading.

...sykryd

Sorry bit of topic dont the 2007 SP models come with 19 standard? mine did but its now causing me problems now with complaince, for some reason they were complanced with 18s.

Sorry bit of topic dont the 2007 SP models come with 19 standard? mine did but its now causing me problems now with complaince, for some reason they were complanced with 18s.

sedan or coupe? coupes come in stock 19s, sedans come in stock 18s. mine is a sedan.

who is doing your compliance? if they are stock rims, i don't see how it would have any compliance issues. might be harder to get the right tyre placard.

got pics of your rims/car?

  • 2 weeks later...

Hi all I have 22s on mine 2008 v36 SP. I am looking for anyone who has the Stock 19s as I sold mine to the shop when I got the 22s. I am interested in a swap for the 22s aswell, Just really want to 19s back.

If anyone is interested pls PM me and we can come to some sort of deal

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...