Jump to content
SAU Community

Recommended Posts

I just came back from the dyno and my GTR did a nice 260 whp at 12 psi with GT-SS ( sarcasm :ph34r: ). My tuner said I NEED to change my cat, we found some piece of the cat on the ground it's really block.

What are my option !? I don't want some cravy 600$ sard or nismo cat. I want to keep the oem look. So, I was thinking about buying a high-flow cat and weld the heat shield on it so I can keep that oem-look.

What do you guys think?

Why do you want to weld the heat shield onto a hi flow cat? Its not like there illegal, people only weld the stock heatshield on when there using a stright pipe to make it look stock.

Hey Cobraa,

If you have a look on Ebay, there are a couple of cats, the main one manufactured by a workshop in western australia that are reasonably cheap $200 - $230 in 4 or 5".

They use 100cpi metal matrix if i remmember correctly and these should flow sufficiently for your GT-SS's and at that price if your really chasing the power you can probably afford to knock the internals out for use on the track :D

I'm after one too

AFter researching Just Jap have the most resonable stock.

Catco/Xforce $175 each bolt on.

450+CFM. $370 for the 700CFM.

I'm probably gonna get the xforce $175 one

*edit btw Catco ones COME with the heatshield.

*edit again, there was a dyno done somewhere, hiflow vs testpipe. No HP difference. Obviously crap cat vs highflow/test pipe would be obvious. So just stick with Hi flow for legality purposes.

There was a test done. Something stupidly low

lame! makes me want to remove mine again, but right now it's the only thing holding back the annoying drone at 2000rpm

X-Force 3" Stainless High Flow Cat

it flows up to 570 cfm...

anyone know what a stock cat would flow roughly?

I got one of these on my r32 gtr making 205awkw @ 6000rpm with just exhaust, pods and 14psi. Seems to do the job good for the price!

X-Force 3" Stainless High Flow Cat

it flows up to 570 cfm...

anyone know what a stock cat would flow roughly?

I would also like to know this!

My muffler shop told me about magnaflow cat.. but that 175$ catco seems right too. Don't know which one flow better.

I got one of these on my r32 gtr making 205awkw @ 6000rpm with just exhaust, pods and 14psi. Seems to do the job good for the price!

http://cgi.ebay.com.au/SS304-4-High-Flow-M...=item2c51eb3c08

Have a look at that bad boy.

Straight pipes all the way mate

I actually run a high flow catalytic converter business, which drastically increases the flow through the unit whilst retaining the standard shell :)

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...