Jump to content
SAU Community

Recommended Posts

I envy the quietness of your car! After a while off loudness you will be wishing you left it as is and IMO the induction noise is way cooler then a loud exhaust note.

If your exhaust flows well and your making the power your happy with and its nice and quiet. Thats something I would wish for before world peace!

I'm a fan for quietness but my exhaust was too restrictive so took out the middle muffler (don't have or need a cat in NZ) and now it goes well and is still not too loud.

Get a hacksaw (or better still a pipe cutter) and cut out your middle muffler and fit a bit of pipe temporarily. If you like the result get it welded in if not you can weld the middle muffler back in.

A loud exhaust is a good way to annoy the neighbours and attract the attention of the police.

Everyone has a different definition of "loud", that much is certain... and often the law has another view all together...

So do what you want TUF250, but just remember its highly likely any mods will almost ensure EPA's will come your way.

Are 3inch pipes any good for the car? Like say from the catback straight pipe no muffler or anything? could it mess my tune up if i change it? as i have a greddy one?

u mean flutes? be noisy as fark dont think its gona do anything to your performance positive or negative.

I dont want it to be silly, I had a V8 previously with just resinators and it sounded great but it really was stupid and eventually got annoying.

Unless my rb is over 4-5k rpm there really is no noise at all. My dads stock xr6 turbo makes more noise! I was just after a burble. Not into cannons, big resinators only or anything like that. Just wanted a bit of burble not bark.

Thats why I thought id leave the rear muffler (the biggest) and remove the centre but I dont want to make it too loud and get myself into trouble.

its a tricky one...

It literally makes almost no noise. It is completely drained drowned out by the induction noise.
If the induction noise is too loud, why not do something about quietening it, like enclosing it in an air box.
3 inch dump pipe high flow cat and lukey turbo muffler 3in 3 out. no police attention but loud enough and seems to flow enough

I have a 4 inch from my T88 turbo back. I had the exhaust custom made with a 4 inch dump coming out pointing at the ground (rotaflo muffler)

It's loud as f**k, on a piston engine it would probably be a little quieter.

  • 2 weeks later...

i've just got a 3" system from turbo back. with a single remus muffler. the sound is sweet. quiet when you're not on the gas and the system is nice and straight so a good note

coming down through the gears. but it has exceptional flow at WOT.

Edited by wacky_will

I would say to be cautious with mucking around with the exhaust chasing a given sound. Odds are you will end up with 'not quite what youre after' and louder than u want.

Quiet is better id say, and im in WA where you can do whatever the f*k you want :down:

My old R33 was loud as. Good for 10% of the time, annoying for the rest.

The current R33 makes twice the power but is quiet as. I love it. Then again i have a pod so it is dead quiet when chilling and an angry tornado under gas. Best of both worlds.

Maybe look at that mod to make turbo induction noise. I think it is a way sweeter noise than exhaust (as good as an RB can sound at the tailpipe) noted by another post above.

I turn way more heads with all induction noise on this one than all exhaust noise on the last one....

And yeah, Vic sounds very cop-strict so a loud exhaust is going to give you nightmares me-thinks.

Goodluck mate

thanks guys, ended up pulling that middle muffler out, quite happy now, only a touch louder and has a slightly deeper note, still very quiet highly doubt it will attract any more attention.

note. I am selling that straight through 3inch stainless muffler if anyone is interested in a high flow 'quiet' muffler

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...