Jump to content
SAU Community

No Compression After Poncam Install

robbo_rb180
 Share

Recommended Posts

robbo_rb180 Grand Master

robbo_rb180

Posted
  • Author
Posted

found out what it was when i removed the cam cover's....... i had the inlet 180 degrees out :)

i had taken the inlet cam vct stuff apart and not re-aligned it properly.

all fixed now

The Dan Grand Master

The Dan

Posted
Posted

Nope, 180 degrees out will not bend valves.....it's just like working the engine in reverse.

You are very lucky.

Buying decent cam gears is a start...only the cheap shitty ones come with two marks....oh and the HKS ones...but once again, shitty.

robbo_rb180 Grand Master

robbo_rb180

Posted
  • Author
Posted
Nope, 180 degrees out will not bend valves.....it's just like working the engine in reverse.

You are very lucky.

Buying decent cam gears is a start...only the cheap shitty ones come with two marks....oh and the HKS ones...but once again, shitty.

i still have std cam gears.

i had it so both in & ex would open at the same time.

next time i will read a workshop manual, instead of just jumping into it.

The Dan Grand Master

The Dan

Posted
Posted
i still have std cam gears.

i had it so both in & ex would open at the same time.

next time i will read a workshop manual, instead of just jumping into it.

wtf?

That would not be 180 degrees out. That's more like 60 degrees out. You are damn lucky!!!!!

Precisely why ppl should not attempt major repairs at home unless they have someone who knows what they are doing with them. Think about how many dollars you would have saved if the pistons collected the valves

PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

My understanding of what happened (and i could be wrong) was that the VCT cam gear was completely pulled apart, then when put back together it was done incorrectly which moved the position of the TDC mark. Then it was put onto the intake camshaft, all TDC were marked up correctly and the belt was put on. So it appeared the belt was on correctly, when looking at the TDC dots, but in fact the VCT cam gear was wrong.

Is that right? Because other than that explanation I don't understand how you can do it incorrectly, the cam gears can only be placed onto the camshaft one way and the dots can only align up one way.

Edited by PM-R33
jiffo Mentor

jiffo

Posted
Posted

Yes the stock inlet cam wheel is adjustable, but from the back so it's a bit of a mission.

Sounds like someone was attempting to adjust the inlet wheel and then didn't re-assemble it all correctly.

Then the normal timing marks would all look to be OK, but the wheel would be referenced wrongly to the cam.

Good way to do some damage.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...