Jump to content
SAU Community

Recommended Posts

Im going back overseas in a few weeks so need to sell my car.

So i had this car for sale about 9 months ago but it didn't sell before i left overseas. Im now back for a short period and need to sell it. I had it for sale for $8500 last time and had 3 offers. 2 of $8000 and 1 of $7750.

http://www.skylinesaustralia.com/forums/Rb...50-t294143.html

Its now been sitting in the garage for 9 months being started every 1 - 2 weeks to keep her fresh. So based on this i am fairly firm on this price of $6750 so please no low balling.

Car is a Wine red R32 with RB25 conversion. Motor has 80 000 km on the clock. Chassis has 150 000 from memory... ill have to confirm that. Also has 12 months rego on it.

The good

Recently the tensioner let go and my valves bent. When replacing them i decided to clean up the whole top end to had all manufacturing imperfections clean up on the head. Also has new head gasket and head surfaced, valves and stem seals, tensioner and idler pulley. Also new exhaust and inlet mani gasket..... so head is pretty much as good as new.

Anyway so car has RB25 conversion.

Still has RB20 g/box.

Mods

Buddy club N+ coilovers all round - Awesome suspension BTW, by far the best ive driven on in its price range.

Greddy type m front mount

3" exhaust turbo back

Exedy heavy duty organic clutch

Few things inside, trust gear knob, omori din gauges.

Bosch 040 fuel pump

unknown aftermarket rear camber arms

Rear spoiler off hole filled and resprayed

32 gtr rear wheels

Turbo smart plumback BOV

What i'd suggest doing

Some of these may well get done if i can find time before i go:

Left rear wheel bearing to be replaced... i have bearing unit sitting in my bedroom, just gotta get out the and change over.

Left rear camber to be adjusted more + or right more - as they are uneven and pulls to the left..... so basically needs a wheel alignment.

It is running rather rich on standard ECU and pops and farts a bit on de-acceleration and dumping a bit too much fuel when it comes on boost, so i'd at-least get a piggy back tune.

Has a dint about the size of a 5c coin on the boot lid, not very deep at all. also a chip about 2mm in diameter on rear quater panel also another small dint on roof. Other than that body is straight.

*** Please note *** I have had the engineering check done for the car and paid half of the fee ($250) there are a couple of small things required for the cert plus the remaining $250. I would allow $1000 to have the car engineered. If you can do mechanical work yourself then maybe a little less. That also includes the cost of the certificate.

So thats all i can think of at the moment. I've tried to explain everything i can think of.

Honestly, this car has been very well looked after. Its rarely driven and serviced regularly with mobil 1.

Id really love to spend a month or so getting it to where i want for sale but i simply dont have time.

Price is $6750.

Located in east burbs of Melbourne

When i can get these photos to upload i will... not working atm for some reason.

The biggest pain for eng cert is it needs side intrusion bars for the doors. I'm looking around for some now. I was just gonna put some on, get the cert, swap them back then re-sell the doors.

Anyway so side intrusion bars, side indicators, tyre placard, baby restraint, noise level test.

For RWC it will be fine. Ride height is actually legal. The exhaust tucks up nice, looks a lower than it is.

I guess wheel bearing would need to be done.

so the car has never been complianced in Australia then as it should have had side intrusions put in and baby restraint fitted to get into the country under either RAWS, SEVS or 15 year rule.

I thought that may have been the next question. Sorry should have cleared that up in previous post.

The previous owner used this as a track car. He changed the doors to ones without side intrusion for weight reduction. Also had interior stripped etc...

So i bought it with RB20 and replaced all the interior and bits he had taken off.... besides the doors. At that stage i wasn't thinking of doing the conversion, nor did i realise it was necessary for engineering.

As for the child restraints....i dont know...maybe he thought it looked a bit silly and took it off... i probably would have done the same :down:

Also, yes it is running standard R33 ECU.

If anyone needs re-assurance i can take a photo of the cpmpliance plates on the car and post them up.

Edited by vitz_n1

**Update** Just serviced her today. New oil and filter, tran fluid, spark plugs, checked timing and compression.

Compression results were 158 158 161 156 160 158, that was with throttle closed, so i was very pleased with these results.

With the timing belt, tensioner, idler pulley, head gasket, exhaust and inlet gasket, valves and seals all replaced she sure is nice and fresh.

Running beautifully!

Also put a new battery and reco'd alternator in as the batt light was starting to come on intermittently and battery draining. All fixed now.

Tyre placard is now done and i bought the side indicators, ill try fond time to wire them up tomorrow.

Thanks mate.

I thought the price was cheap as well. I had heaps more interest 9 months ago when the I was asking $1250 more.

Possibly the price is leading people to believe the car is in bad condition or something wrong with it. I can assure everyone this is not the case and i just need to sell her!

does look very clean..

JiN_MaN: think regency would believe you if you swapped the doors with black 32doors that have intrusion bars? and say you bought it like that ect

What makes you think it doesn't already have them?

*vitz_n1* Hope you dont mind, at least we are keeping your thread at the top

Edited by JiN_MaN

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...