Jump to content
SAU Community

Recommended Posts

Shit sorry dude i didnt notice, I know you've had it for a while but didnt realize it was arthur dunger..I will revert to my old avatar again... :)

lol i dont mind at all mate! :)

more paul hogan love! ;)

Link to comment
https://www.sau.com.au/forums/topic/329372-r33-gtst/page/2/#findComment-5357970
Share on other sites

And yes Kinks, i just witnessed my mate slide off a bank into three trees yesterday in his Alfa 33, because he accelerated mid corner, car is totaled and he is lucky he or anyone else wasn't hurt. I was behind him in my MX6, very scary. I do enjoy to occasionally boost, but i wouldnt put my self in a situation where i was risking running such a beautiful car (R33) off the road :( And im very keen to take an advanced driving course, as soon as i can afford it lol

Oh and its a Type-M, i googled for ages and could not find any difference between a Type-M and a non Type-M, is there any difference at all?

He probably did it a few grand worth of improvement, if it's an Alfa ;)

The whole type M non-type M thing is all just bullshit.. some people reckon body kit = type m. if you have a 2.5L turbo with a manual then you are driving an awesome car. everything else is just an option that the original owner either ticked or didn't tick when they bought the car.

I understand what you're saying here, but on a standard skyline the nose will push wide first, ie they are still set up to understeer first assuming you dont put the boot into it.

bull shit! what car are you driving? My car with stock standard ORIGINAL suspension (34,000km genuine k's) and wheels/tyres will flick the tail out before even thinking about understeering. it is VERY tail happy on the throttle, perfectly controllable and a joy to drive but I have never understeered in it. you would have to go ridiculously quick into a corner for it to plough on, and never on the throttle. throttle = tail out. end of story.

don't accelerate around corners

accelerate before the corner, flick the wheel and keep the boot in ;)

so you've seen how i drive! :)

Link to comment
https://www.sau.com.au/forums/topic/329372-r33-gtst/page/2/#findComment-5360831
Share on other sites

just remember your manners when talking to police after you get pulled over.. Might make all the difference.

cops have been no worse for me than in any other car. i have never been anything but polite to them and if you pass the attitude check they will treat you like a human being in return.

if you go off half cocked like your average lebbo f**kwit "I wasn't doing nuffink!!" (sorry to stereotype) then you get what you deserve.

Link to comment
https://www.sau.com.au/forums/topic/329372-r33-gtst/page/2/#findComment-5360834
Share on other sites

bull shit! what car are you driving? My car with stock standard ORIGINAL suspension (34,000km genuine k's) and wheels/tyres will flick the tail out before even thinking about understeering. it is VERY tail happy on the throttle, perfectly controllable and a joy to drive but I have never understeered in it. you would have to go ridiculously quick into a corner for it to plough on, and never on the throttle. throttle = tail out. end of story.

I said AS LONG AS you don't put the boot in. Turn in at speed with no throttle, and the car will understeer. Which is what it should do.

Also I wouldn't call stock suspension a joy to drive.. its relatively comfortable but much too soft and squidgy for my tastes.

But as I'm getting off topic, I'll shut up.

Link to comment
https://www.sau.com.au/forums/topic/329372-r33-gtst/page/2/#findComment-5361346
Share on other sites

I said AS LONG AS you don't put the boot in. Turn in at speed with no throttle, and the car will understeer. Which is what it should do.

Also I wouldn't call stock suspension a joy to drive.. its relatively comfortable but much too soft and squidgy for my tastes.

But as I'm getting off topic, I'll shut up.

any car will do that. it's physics. even a F1 car will understeer if you go into a corner too fast. fwd cars can be prone to lift off oversteer, but so can rwd cars.

any half powerful rwd car will slide the tail out if you boot it mid corner as well, whether it be a skyline or a commodore. but a stock turbo skyline isn't exactly anything be scared of. even up around 200kw they are still pretty ordinary and unless it's wet or you have really crappy tyres, booting it round a corner in 2nd gear or higher isn't going to end badly unless you boot it then really start swinging on the wheel to try and get the back to kick out.

Link to comment
https://www.sau.com.au/forums/topic/329372-r33-gtst/page/2/#findComment-5361787
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...