Jump to content
SAU Community

Recommended Posts

hi, wrecking a black r33 gtst in melborune. have a complete car so if ive missed anything feel free to let me know. prices are as follows. open to offers

hks hypermax drag coilovers hardly used. 1300

r33 highflow turbo (made 230rwkw on 13psi) only done 1000kms on it no shaft play. 750

sard 850cc side feed injectors 600

tomei poncams brand new in box 670

hks actuator 70

r33 intercooler kit. 180

400r front bar with 400r indicators 370

veilside skirts 130

boot + gtr wing 350

19" xhp jet rims with low profile tyres 1500

power fc with hand controller has tune on it also 1200

z32 afm + plug 250

xtreme organic clutch, near new 350

rb25det gearbox make an offer

rb25det engine rebuilt to standard spec by dr drift 2000kms ago. make an offer.

standard rb25det manual ecu 80

standard intercooler 50

standard rb25det afm 80

slotted front rotors near new 250

Edited by skyline25t
Link to comment
https://www.sau.com.au/forums/topic/330752-wrecking-black-r33-melbourne/
Share on other sites

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

hi, wrecking a black r33 gtst in melborune. have a complete car so if ive missed anything feel free to let me know. prices are as follows. open to offers

hks hypermax drag coilovers hardly used. 1300

r33 highflow turbo (made 230rwkw on 13psi) only done 1000kms on it no shaft play. 750

sard 850cc side feed injectors 600

tomei poncams brand new in box 670

hks actuator 70

r33 intercooler kit. 180

400r front bar with 400r indicators 370

veilside skirts 130

boot + gtr wing 350

19" xhp jet rims with low profile tyres 1500

power fc with hand controller has tune on it also 1200

z32 afm + plug 250

xtreme organic clutch, near new 350

rb25det gearbox make an offer

rb25det engine rebuilt to standard spec by dr drift 2000kms ago. make an offer.

standard rb25det manual ecu 80

standard intercooler 50

standard rb25det afm 80

slotted front rotors near new 250

anything wrong with the rolling chassis?

if not how much you want for it with suspension

and a price with suspension engine and box, cheers

hi people,

* there is nothing wrong with the car, have been trying to sell it for a while and every1 has tried to stuff around with price with all the parts on it so going to wreck it.

* not sure what the going rate is for a rolling chassis,suspension, engine, and gbox. pm me ur offer.

* i can pm some pics of the z32 afm on saturday as i'm flat out with work this week.

* series 1 tomei poncams, IN/EX 256 duration and 8.5mm lift (they're standard rb25det lift so they drop straight in) $650 delivered.

* i have a clutch master cylinder. make an offer.

Hey mate,

whats the condition of the starter motor? any whines on startup?

also, $30 bucks pickup for the the glove box assembly?

what area around melb are you from?

Call shotgun on engine complete with poncams & injectors as per phone convo...

Can anyone help with Shipping quote from VIC to NSW???

Never sent/recieved a motor interstate before

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...