Jump to content
SAU Community

Recommended Posts

hey dude, would the coil pack fit a s 1.5 ? would you have a radiator??

To fit the coil packs you would need an igniter and a heap of wiring changes.

I have a 40(ish)mm thick Alloy radiator $120 pick up only its too big and fragile to post imo

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

Well time for the skyline to go, No time or motivation or money to finish it

So instead of selling it whole Im stripping it.

Pick up Preferred for large parts. In Canberra.

Ill start with the big stuff,

R33 Rolling shell, comes with gearbox and motor if you want them - $3500 with bare RB25DET long motor (no manifolds, turbos etc etc) os Giken Twin Plate Comp Clutch (the 600hp rated one) about 1/2 worn, 5 Speed 25det box, has Nismo Clutch Pivot Ball, Walbro Intank pump, FMIC blah blah blah,

Tein Super Street Coilovers, Whitline 22mm Adjustable rear sway bar, Tomei Hicas Canceller, Ajdustable Upper Camber arms front and rear, the fronts have seen ZERO Use!

It has stuff all interior left in it, Wiring looms have been pulled out and are sitting on the garage floor.

Brakes are Standard Calipers with RDA Slotted rotors, and QFM K500 Pads are in atm.

There is a heap of other stuff too, but cant remember it all

This is bloody cheap for what it is! The Clutch and gearbox are worth more than what im asking for a nearly complete car.

Also Selling a Greddy Copy Plenum with standard thottle body - $250, not very old and in good nick, no leaks and fits fine.

740cc High-flow RB25 Injectors in factory rail and with factory fuel reg - $200

Microtech Lt-12s Plug and play ECU for R32-33 Gtst's and GTRs comes with 4-line handcontroller - $750

Greddy E-Manage Ultimate N-4 Harness only suits R32-33 Skylines - $100

Alloy Surge Tank with hose tail ends, about 1.5 or 2L from memory Un-used - $50.

There is heaps more that I cant think of at the moment.

And Questions Just ask, Pm Is best

Thanks

Andrew

hey mate can u post some pics up of the inlet plenum.. email them to me if u want, [email protected]

Ok due to lack of time and a few people pulling out of buying things.

for 1500 bucks you get everything thats left inculding the shell,

thats RB25 long motor, fresh RB30 Short motor, OS GIKEN Twin plate, Gearbox, brakes, diff, etc etc.

So bring a trailer and some wheels and get it out of my sight.

Hey Zebra,

If you still have a starter motor to fit an R33 i need one as mine died yesterday. Im Canberra so can pick up on the weekend if you still have one.

email me at adammooreis[at]hotmail[dot]com

Adam

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...