Jump to content
SAU Community

What Gasket And Do I Need To Weld Block Water Jacket

30ed32

By 30ed32,
in Engines & Forced Induction

 Share

Recommended Posts

30ed32 Enthusiast

30ed32

Posted
Posted

I need a bit of help here with those two things believe me I have searched and haven't found a definite answer. So the plan is to have use a rb25de head from a r33 and a rb30 block, from what I've found people are saying it doesn't matter what head gasket I use, 25 and 30 will both work. Although I am trying to save money where I can here and would prefer to not have to get the block welded and machined flat again. Some say its recommended to weld the water jacket on the block so that you have more surface sealing the water, but can't I just use a rb30 head gasket and everything will be alright? Going from these pictures that I have found:

30 gasket on 30:

http://www4.wave.co.nz/~lakewood/Skyline/R...s-RB30Block.jpg

25 gasket on 30:

http://www4.wave.co.nz/~lakewood/Skyline/R...-RB25Gasket.jpg

The oil gallery on the head will be seal obviously, most likely by using a grub screw as some people have used and it seems cheaper. So if the vvt feed is blocked on the head is it alright to use a rb30 HG so that the water jacket will seal better?

Thank you

jarrod83 Community Regular

jarrod83

Posted
Posted

compare both gaskets with the rb25de head, you should be able to see what gasket works best for you.

I used the rb30 gasket with a rb25det head, but i already had to modify the head to block the vct oil feed so i just added some meat on the head while i was at it, personally id make the modifications to the head so that if you ever needed to replace the block, it would be a lot easier

Jarrod

30ed32 Enthusiast

30ed32

Posted
  • Author
Posted

Thanks for the feedback guys, I was under the impression that it was the block that needed to be welded and machined to suit the gasket. Thats what I gathered from this picture anyway.

http://www4.wave.co.nz/~lakewood/Skyline/R...30%20Gasket.jpg

30ed32 Enthusiast

30ed32

Posted
  • Author
Posted (edited)
Use an RB30 or RB26 gasket and with 25DET it's the head that needs welded.

Oh thats good, I'll be using a 25DE head so that saves me some hassle. I also have a 25DET head so I can compare the differences when i take the 25DE head off the motor. Anyway using RB30 or RB26 head gasket, I won't have to weld a bigger area on the block? Or is that wrong?

Edited by 30ed32
fletch rb30 Enthusiast

fletch rb30

Posted
Posted

r33 25de and det heads are the same.

the engine builder we use uses an aluminium mig welder and fills in the front water port a bit and fills in the oil feed then gives the head a skim. Its not very expensive.

By doing that you can fit the head to any unmodified rb30 block and use any rb30, rb26 or r32 rb25 gasket

30ed32 Enthusiast

30ed32

Posted
  • Author
Posted

sweet, I'm in Hamilton btw and only know one engine place here and don't think they will do it and if they did it they would charge a lot. Hopefully I can find another one.. it's not really worth the trip up to Auckland unless i can't find anyone.

jarrod83 Community Regular

jarrod83

Posted
Posted

the de head doesnt have the vct so it doesnt have the vct oil feed in the head that has to be blocked like the det head, it didnt take long or cost me much to get the head welded, took them maybe 5 mins to weld some metal in.. they let me die grind it abit, they smoothed it up, then the head got deck

Jarrod

fletch rb30 Enthusiast

fletch rb30

Posted
Posted
sweet, I'm in Hamilton btw and only know one engine place here and don't think they will do it and if they did it they would charge a lot. Hopefully I can find another one.. it's not really worth the trip up to Auckland unless i can't find anyone.

give Dick a call at hytech engine reconditioners in manukau. only an hour away from you. they have done all the heads for me and my friends rb30's. dont remember what it cost, but it was a reasonable price and he has done plenty of them

the de head doesnt have the vct so it doesnt have the vct oil feed in the head that has to be blocked like the det head,

Jarrod

the r33 head does, just not the r32

bubba Grand Master

bubba

Posted
Posted
the de head doesnt have the vct so it doesnt have the vct oil feed in the head that has to be blocked like the det head, it didnt take long or cost me much to get the head welded, took them maybe 5 mins to weld some metal in.. they let me die grind it abit, they smoothed it up, then the head got deck

Jarrod

the r33 head does, just not the r32

R32 RB25DE head is straight plug and play, no modifications necessary.

R33 RB25DE/T heads have to be welded up.

30ed32 Enthusiast

30ed32

Posted
  • Author
Posted

thanks everyone for clearing that up. Maybe it would be easier to pick up a cheap r32 25de head? This is going into an R33 btw, and I have heard something about the intake manifolds not fitting or something? Would the 32 head be plug and play in a r33 using all the r33 parts that attach to the head?

bubba Grand Master

bubba

Posted
Posted
thanks everyone for clearing that up. Maybe it would be easier to pick up a cheap r32 25de head? This is going into an R33 btw, and I have heard something about the intake manifolds not fitting or something? Would the 32 head be plug and play in a r33 using all the r33 parts that attach to the head?

The intake manifold bolt layout is different, the R32 RB25DE head is the same as RB20 and R33 RB25 intake manifold don't fit on RB20 heads.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

I am using an RB25DE head retaining the VVT. I understand they have bigger valves than the RB25DET heads. Gasket is a Tomei RB25 item.

+1 for ringing Dick at Hytech engines - he does a lot of RB30 stuff and you can always courier him the head if necessary although its just over an hour's drive away if you need to take the block in.

30ed32 Enthusiast

30ed32

Posted
  • Author
Posted

yeah thanks guys i think thats my best bet is taking the head to hytec and get them to match the gasket.. some people are saying head some are saying block? I guess i'll have a look when i get the heads off and compare gaskets and go from there.

30ed32 Enthusiast

30ed32

Posted
  • Author
Posted

thanks I remember seeing that a while ago i just forgot, it doesn't look like there was any extra welded on... just vvt blocked and the hole reshaped, but thats probably just me not looking closely enough. Thanks for all your help I will take head into hytec and get them to sort it out for me.

30ed32 Enthusiast

30ed32

Posted
  • Author
Posted
definately 100% the head thats needs modifying

awesome.. just hope its cheap enough and i hope this helps someone else out in the future, maybe I'm just a bad researcher but I couldn't find such definite answers anywhere else. Thanks guys should be running in a few weeks hopefully once I have all the parts

  • 2 weeks later...
Gerg_R31 Mentor

Gerg_R31

Posted
Posted

all rb25's run same size valves, rb26 valve heads are 1mm bigger then the rb25

the rb25's with vvt have an oil return under the intake cam, which fouls with the water jacket in the rb30 which will mix water and oil, dont want to weld it? tap it and lock tite a grub screw in, want to still use vvt or just drain the oil tap the hole in the front

there is no other welding needed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...