Jump to content
SAU Community

Recommended Posts

hi everyone,

i have a harsh airflow drop after ~6300 rpm, at aproximately ~4,4v at Z32 MAF. It feels like i just lift foot of the pedal. When i look at the Datalogit charts i can see that the airflow drops earlier than boost.

I suspected the stock rubber suction pipe being sucked inside under boost and just changed it to a silicon type ebay item enforced with metal rings. I also changed the air filter to the new apexi panel filter in the stock box. but no use.

the cars still shuts after ~6300 rpm.

what else can it be? some kind of full-throttle compressor surge or what? is there any way to diagnose suction pipe sucking itself on the road without a dyno?

p.s. it`s rb25 with rb26 crank and rb26 forgies, hks 256/8,8 cams and GT2871R (without port shroud) running 0.8 - 1 bar boost.

thanks.

Link to comment
https://www.sau.com.au/forums/topic/333769-the-car-shuts-after-6000-rpm/
Share on other sites

Check exhaust? does boost drop off? timing etc.

boost drops _after_ airflow.

timing is ok.

exhaust... it`s a split dump pipe from ebay, frontpipe + decat pipe in one piece and fujitsubo exhaiust. the only new part is a splitdump but it seems ok. how should i check it?

and one more thing: usually the first run at is ok -- the car pulls ok to the redline. but other runs at 1 bar have this problem. On very hot days after traffic the problem appears even at 0.8bar.

i had a very similar problem and it turned out to be bad coils. gets worse as you run more boost, and the sudden drop is very violent, mine also performed slightly better in colder conditions.. if its the coils then you run the risk of doing damage to your bearings if you continue to drive it like this. whatever it is, stay off the boost/revs until its fixed

Knock sensors, you get 1 rev to red line then it will retard once its gets to a certain rpm untill the ignition is turned off then back on.

to check this, just turn engine off while moving then turn on again and rev right through to red line to see if its gone and then returns

on next gear rev to red line.

Faulty AFM?

Try swapping with another.

but what is it`s fault? its voltage is ok. it`s voltage drop is ok too as it follows real "pedal lift" effect. but thanks for advise - i`ll try to find another z32 afm.

ok let me ask in other way: is there anyone here running gt2871r or smth similar on rb25 with the stock rubber suction pipe (or silicon type from perfomancewise) and stock airbox? do you have any issues like written above?

thank you.

and one more thing: usually the first run at is ok -- the car pulls ok to the redline. but other runs at 1 bar have this problem. On very hot days after traffic the problem appears even at 0.8bar.

I think your on the money already. The intake pipe sucks in easier when its hot. I fixed this issue temporarily with some coat hanger wire wrapped around the intake pipe to keep it circular. The silicon intake pipe without rings fixed it and flows better. this was on a Rb25 with GT2835.

Edited by BoostdR
ok let me ask in other way: is there anyone here running gt2871r or smth similar on rb25 with the stock rubber suction pipe (or silicon type from perfomancewise) and stock airbox? do you have any issues like written above?

thank you.

Yep HKS GTRS on S2 Stagea with K&N filter. The cut and insert solid pipe per rev210 and issue gone.

You still need to be mindful that the filter can be a restriction causing the pipe walls to suck in so the filter should be cleaned if dirty or replaced as needed.

Yep HKS GTRS on S2 Stagea with K&N filter. The cut and insert solid pipe per rev210 and issue gone.

You still need to be mindful that the filter can be a restriction causing the pipe walls to suck in so the filter should be cleaned if dirty or replaced as needed.

yes, thanks, as i wrote new apexi panel filter was just installed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I used to have Walbro 255's when they were a pretty common update. (or were they 044? 040?) In any case I had a dirty tank. I thought the tank was good, but I would find the filter would clog in maybe ~50km of driving. If the issue persists, well, your fuel system or tank has crap in it that the pump is sucking up.
    • Hi. Ok thanks for the info. I/we do not know what tune is on that Nistune ECU so it is why there is stock ECU and that Nistune is for later when the car is done. I have guy who tunes Nistune and other ECU so i will then take it to him to see and properly tune for the car   And for the update. On 99,9% it is bad fuel pump. Which is wierd cuz it is like 2 years old(brand new walbro 255) and that filter (also brand new) was dirty.  I was alwaya pumped premium(100) on very good petrol station so i dont know how is that possible...  
    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
×
×
  • Create New...