Jump to content
SAU Community

Are The Rumours True?

Astro Bear

By Astro Bear,
in Victoria

 Share

Recommended Posts

CrispyFries Grand Master

CrispyFries

Posted
Posted
And WTF are they doing. 39.9% is not full, so it is rather irresponsible to lighten restrictions going into spring/summer...

The north south pipeline was switch on this year, so that's probably part of the decision

Edit: Ahhh yeah... what Greg said ^^^

(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted
The only thing stopping me from washing my car now is time :D Too freaken busy :O

You have listed a Supra / 300ZX / MR2, which are the cars you "did" have, you would be busy washing 3 cars on your own.

:(

jezza boii Grand Master

jezza boii

Posted
Posted
You have listed a Supra / 300ZX / MR2, which are the cars you "did" have, you would be busy washing 3 cars on your own.

:(

Yeah, I need to change that :D Just refer to my sig for my car list.

ashneel Grand Master

ashneel

Posted
Posted

You can now wash your car at home using a bucket or a high pressure cleaning device

- You cannot use a hose to wash your car

- You can of course use rainwater as you could under all stages of restrictions

This change has been made possible through a combination of factors:

- Melburnians commitment to water conservation the community has saved an additional 34 billion litres since the start of the voluntary Target 155 campaign. Melburnians have used just under 150 litres per person since the target 155 campaign commenced, a tremendous result.

- New sources of water are now on line and these add a new level of security and include the Tarago Reservoir and the North South Pipeline

- We have had much better rains. We had enough rain in Autumn to thoroughly wet the catchments and with the good winter rains storages are rising at over 1% per week. Currently our water storages are ~12% higher than the same time last year which equates to about six months consumption.

- Work on the new Desalination Plant at Wonthaggi is progressing very well, with completion still on track for late 2011. The desal plan will add another 150 Billion litres per annum which is about 42% of current annual water usage

UNR33L Grand Master

UNR33L

Posted
Posted

I think if i hooked up my high preasure hose people walking the street would give me dirty looks just like when i washed my dirt bikes with it.. there like WTF ARE YOU DOING?!?! SAVE THE WHALES

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...