Jump to content
SAU Community

Recommended Posts

Hey Ppls.

Also, I had a run done with and without my exhaust silencer (which I will also post up) and the results are remarkable.  HUGE drop in power through the whole rev range, as well as big boost drop up top.

Anyway, stay posted for pictures.

BASS OUT

hey dude,

i also have a silencer and after i fitted a turbo back zorst and a boost guage i have noticed the most i will hit (psi) is prob just under 9 ish, so about 8-9 then it drops to about 5-6 ish right b4 red line... So can you tell me what the results were like when you removed it...as i think im gona remove it ....guesss ill have to risk another yellow sticker for some extra power!

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

the oak: yeah it will be cos the silencer is the bottleneck in the exhaust system (im pretty sure)

bass junky: did you notice the power band change at all after changing the cam? as in you could making the same max power in rwkw but you may find it'll pick up quicker and hit boost quicker as the cam gear gives more low end torque but still gives the same top end rwkw figure, it just gets there quicker and sharper

Here's the Dyno Charts

First (Dyno with and without silencer) is the first run before any work was done.

It shows the power with the silencer in and out.

You can quite obviously see the 20kW and 0.1bar (1.5 psi) of difference.

I was expecting this, and it really shows the value of a good exhaust.

Second (Dyno with and without cam gear) is the runs with the cam gear installed and then the subsequent runs again trying to extract some power from it, but obviously not luck. The car was strapped to the rollers the whole time and was worked on in the dyno cell.

During this period the car was pinging quite readily as the fuel was Ampol "Premium" from Bendigo and the operator could induce pinging at 2500 rpm, standard computer was pulling timing a bit during this period, but all the lines are exactly the same, so there was no obvoius gain.

Third (Dyno final with Optimax) is the final run after the tank had been drained and some optimax was fitted. Again, no gain and the shape of the graph is identical to all others. You can also see the A/F Ratios richen right up in the top range.

So there you have it, and expensive day on the dyno for sweet FA.

The only comfort I can seem to come by is that maybe the difference in the weight of the standard pulley compared to the HKS one might give me a slight advantage due to reducing the rotating mass.

Anyway, I hope you can glean something from this all those R-34 drivers.

Maybe the differnt cams and heads in our cars make adjustable cam gears redundant.

I think I remember somebody saying that cam timing is how nissan retricted the cars in power, so with the magix 208kw in the R-34, the timing was optimized.

Now to go and fit a Power FC to try to fiddle with it some more!!

BASS OUT

Hi guys, I am sorry but I don't understand why setting it up on the lobes centres on a DOHC engine is important when you are going to move the camshaft timing to where it produces the best power curve on the dyno. I spend an hour or two setting it up on say 118 degrees. That's seems like a huge waste of time to me. I am going to rotate the cams with the adjustable pulleys and take regular dyno readings to achieve the position that gives me the power curve I want. I don't really care whether that's 124 degrees or 112 degrees, as long as it makes the power where I want it.

When we had no dyno, or (heaven forbid) a unaccessable (on the dyno) single cam engine, then setting cams up to the specs was important. But on a Skyline with easy access to a dyno, it's a waste of time.

Moving onto the reason for this thread....

I have only had 2 Skylines that didn't benefit from retarding the exhaust camshaft timing, both were R34s'GTT's, both had Tomei Poncams in them and both had Power FC's. Nothing we did would make more power anywhere, compared to the standard timing position. I always put this down to the Poncams being very accurate from Tomei (ie; they got it right).

It will be interesting to see what happens when Bass Junky (or someone else with an R34 GTT) uses a tuneable ECU with an adjustable pulley on the standard camshafts. I, for one, am gunna watch this space.

I've gotta say that that is just freakish, same bumps and dips in the curve and everything.

Did you try playing around with the cam timing anymore after the 4deg retarded run? Because a change of that magnitude will have some sort of effect, no matter how small. You seem to have no effect except for minor variations that may be attributed to different environmental conditions.

Is it definately an R34 exhaust cam wheel and not r33? do they have a differnt locating pin position like say an s13 vs s14 inlet cam? Only reason i ask is because those two curves look to be made by an engine that is identical.

Did you try a run at -4 then wind the cam timing back to 0, i reckon somethings out mate, no matter who did the work.

yes move then to where is good!I agree!But i prefered to 1st set up the cam to where the specs that the cam comes with and take it from there.....I would say that sydneykid sounds like he has quite a bit of experience....so any of his advice is good advice :D sk

Like the rest of you, I am perplexed (and I don't like being perplexed). Let's say Nissan got it SPOT ON with the R34 GTT camshaft timing. Then if you retarded it 4 degrees, it would be 4 degrees WRONG!. Thus it would make LESS power, not the same power. Certainly not EXACTLY the same everywhere in the power curve. So that explanation is illogical.

I remain perplexed.

Just a thought so don't flame me here :D

Running crappy fuel and getting the motor to ping (like he did) is gunna make the ECU retard the crap out of the timing right ??

Then going straight to good fuel without resetting the ECU isn't going to do that much cause the ECU has already retarded the ignition.....

I mean, is that how the ECU works? Once it's detected pinging, will it leave the timing retarded all the time until you reset it ?

I say give the ECU a reset and see how it feels. Won't cost you anything except about 15 minutes of your time....

It's got me stuffed that it made NO difference, neither gained or lost power....

Or maybe a REALLY stretched or slack cam belt ??

Now I'm really stabbing in the dark.. :)

J

I can see where Sydneykid is coming from on this, but It really would be nice to know where both cams were in the first test, and where they were in the second test.

Jay is right about cam belt tension as well. If you really heave down on the tensioner you can easily move both cams a lot more than four degrees.

It really was a pointless exercise the way it was done. And no reflection on the workshop involved either. If the customers says dyno my car, than fit that pulley at -4 and dyno it again, that is exactly what was done. Now the result is total confusion.

At the very least the locations of both cams should have been measured after the second test so that they could be returned to that figure later on.

Was the ignition timing checked before the first run? probably not.

Its a bit like stuffing around with ignition timing on the dyno and after many runs saying yep, we picked up some power by advancing it a bit. Later the timing belt has to be replaced, and it is impossible to return the engine to the "good " ignition timing figure because nobody thought to record exactly where it was.

Its really no good saying that it does not matter, every time you adjust the timing belt tension it needs ten dyno runs to get it back to being right, because THAT is the only way to know for sure. Well, yes, and no. I would rather use a timing light, and every time I do an oil change, just have a quick look to see it has not moved from where I know is right.

As far as the ripples in the power curve go, all sorts of tuning factors such as fuel and spark mapping come into it besides small changes in valve timing, and none of those were touched.

The results while unusual, do not surprise me in the least. And yes the factory have changed the valve timing figures quite a bit for different RB engines and different model years. The cams themselves always have the bump exactly at the lobe centre of the first lobe. That is how they are ground on the cam grinding machine.

So the difference in factory lobe centre timing is done with the pulleys. So a set of aftermarket pulleys that will fit any RB engine and are set to zero, might do quite different things to different model years of RB20, RB25, RB26 and so on.

There is a lot more to it than just fitting a brightly coloured cam pulley and setting it to four degrees retarded, and expecting to pick up 15Kw every time.

Time and time again I hear, Yeah and fitting those pulleys will give me an extra 15 to 20Kw, and also I am gunna get a...........

my simple take on the matter is that you have a problem somewhere between the fittment of the new cam gear.

If the factory method was followed this involves the removal and replacement of the cam belt etc..

In most installs the existing cam belt is simply stretched to allow the fittment, this is not a great thing to do on a fairly old belt. The additional stretch may cause an issue. Why not rip out the dial guage and see where things are again?

This is not issolated to R34's , a person who did this on his R33 I know of had the same net result the difference being he experienced a loss of power at any other setting other than factory.

As in his instance there is always an underlying issue. Heat soak in a dyno environment can rob the modest power gains as well.

The thing that really gets me, and points to perhaps another problem is the fact that it didnt make much difference - 4 degrees is enough that you should have notice some result, be it either an improvement or reduction in power.

Sure the cams may be dialed in from the factory, but the power curve should change.

  • 1 month later...

I also had no bloody luck, when it came to tuning my cam gear, infact I lost power.

My engine is a series 2 RB25DET (1996 ECU) running 7 psi of boost.

With the cam gear set at zero degrees, it put down 154 Kw, with A/F ratio's almost spot on at 12:1

With the cam gear set at 2 degrees retard, it lost about 10 Kw, as the A/F ratioswent to 11:1. I believe if the A/F stayed at 12:1 I would have got more power, as the power curve looked to develop peak power later in the rev range.

We didn't go any further with the cam timing, as time is money, and it looked as though there was nothing to be gained with my Std computer.

Any thoughts?

At a guess, and it is a guess, so dont flame me if I am wrong, it sounds like the base timing wasnt reset properly. It doesnt seem to be a very uncommon problem.

I had the same thing, back to back dynos - but the operator 'guestimated' the CAS position, based on the initial timing setting marks on the CAS. Its pretty common when removing the CAS to put a small mark on it and the cam gear cover so the mech knows approximately where to relocate it before attempting to start the engine.

Unfortuneately when I had it done the first time the operator insisted that the way he was doing it was correct, and that the best setting for an exhaust cam gear was only around 1-2deg retard. He was able to prove his point with his method.

I then took the car to another place, he restet the timing with a timing light, and I picked up 15rwkw through the mid range going from -2 to -4 deg.

Is the cam gear still set to 2 deg retard?

No we set it back to zero, and the power picked up again.

I think you are spot on with the ignition timing, that's exactly what he did (put a mark on the cam cover, to line it back up on). I asked about the timing light, and he wasn't sure that you could use one on a skyline!

I guess that's what you get for using a Dyno operator in Nowra, he still happily took my $200 though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
×
×
  • Create New...