Jump to content
SAU Community

Recommended Posts

I currently have a GT3040R .82 on my rb20 which i believe is a GT3082R?

I’m currently running 21psi and plan to screw in another 4-5psi, is this still in the efficiency map for this turbo?

at the moment the engine is making 10hp/psi and has made 371rwhp @ 7300rpm

at what point would you go a 1.06 rear housing or would you go a GT35R with a .82 rear. what is the difference from the obvious?

what are these turbos rated hp wise with the 3 different rear housing options?

what would the response/lag difference be between each combo

for a reference im making 5psi @ 4300rpm and ramps hard to 5500rpm making 17psi

what would be the next step with the turbo, my goal is another 50-70hp

Thanks Luke

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/
Share on other sites

On a RB25 i made 270rwkw @ 17psi with a GT3040 (600hp) in a .82

If you get a GT35, it'll be laggier, simple as that. Its a larger comp wheel so its going to be slower.

Given then 600hp GT30 should do 330rwkw, you need more boost.

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422243
Share on other sites

If you get a GT35, it'll be laggier, simple as that. Its a larger comp wheel so its going to be slower.

Given then 600hp GT30 should do 330rwkw, you need more boost.

yes will have more lag but just how much, 500rpm, 1000rpm for same boost.

330rwkw on a 25 or 20 and at what psi

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422279
Share on other sites

How do you know its not coming into another area of efficiecny and so on where the power gains are more than 10hp/psi?

IMO much below 24-25psi and the turbo isn't really in its happiest place given i should have been running closer to 20-21psi on a 2.5ltr

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422362
Share on other sites

the next step up is the GT35, in 0.82 form it will do 350-380rwkw.

that is going to be very laggy on a little RB20, you will have ~1000-2000rpm of full boost before you have to change gear again. if its just to get the number is it really worth it?

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422364
Share on other sites

the next step up is the GT35, in 0.82 form it will do 350-380rwkw.

that is going to be very laggy on a little RB20, you will have ~1000-2000rpm of full boost before you have to change gear again. if its just to get the number is it really worth it?

Nitrous, E85 - two much better ways to get that little bit more power

Or just alter the dyno setting, for 40hp I'm not sure the need for the hair splitting...

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422370
Share on other sites

but will it do another 100hp.

Probably, if your motor can.

Whats done to your motor? Your coming in fairly late with only 5psi by 4300, I know the gibson RB20 had powerband between 6 and 8 yet a 1:1 bump on the static CR and a 3 psi drop in boost saw it with usable power between 4 and 8... MASSIVE difference.

Tell us more about your motor.

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422443
Share on other sites

40thou over size arias pistons, spool rods, ported head, 264 cams 8.5mm lift, 8.7cr. high mount 3040, rb26 intake and throttles,

changing intake to 80mm tb and new plenum on half standard runners to make a little more torque. cam gears set at odeg atm.

720cc injectors, toda light weight flywheel,

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422464
Share on other sites

Leave the throttle, try get the gears dialed up. For interest sake I would also try dialing them with the stock intake cam.

Your motor sounds like it can make the power, just need to push the turbo into efficiency along with the tune to match. 25PSI and a good dial on the gears should get you the power Ash is talking about (30rwkw) if not more IMO.

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422601
Share on other sites

Nismoid the Garret turbine maps actually show the flow rates of the 0.82 GT30 and the 0.63 GT35 as having similar maximums though IMO the GT30 0.82 is the better map , these are with the T3 flanged GT30 turbine housings BTW because the 30 and 35 both use them .

Not my project and don't think I'd build such a top endy RB20 but to each their own .

Now there is another option in the GT3082R family and its what used to be called GT3040 in HKS speak .

What it is is same deal as the Garrett GT3082R/GT3040 but with a 50 trim rather than 56 trim GT40 compressor wheel in it .

My old HKS list shows its good for 20 more PS/Hp than a GT3037S/GT3076R 56 trim .

I have a compressor map of a Garret large frame plain bearing GT4082 which uses this same compressor wheel and it shows the the maximum airflow rate at the bleeding edge of about 57 lbs so potentially 570 Hp if you go by maximums .

This is in a 0.58 A/R GT40 compressor housing which is crudely speaking of a similar size externally to a T04S o.70 A/R one , maybe a smidge smaller but port shrouded .

It may even pay the OP to look into Mitsubishi turbos because they tend to use reasonably big wheels in smaller trims than Garrett does sometimes and that could pay off when you want power over as broad a range as possible .

BTW what does the OP want to do with this RB20 ?

A .

Link to comment
https://www.sau.com.au/forums/topic/334874-gt30r-vs-gt35r/#findComment-5422747
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...