Jump to content
SAU Community

Think My Turbo Is Dying

southern_tango
 Share

Recommended Posts

southern_tango Proficient

southern_tango

Posted
Posted

Yesterday after work ,my car made a metallic noise ,and boost didn't go over cero after driving a bit more noise went away and boost was back,so I though that was it just a mere boost drop.

But this morning it happened again,noise ,no boost but no smoke or anything else and after 2 minutes all normal...but when i put my ear next to the pod i still can hear a metallic hsssss.so the louder noise looks to happen when car is cold

Now,that this mean my turbo is going to die?what could I espect to happen?

(I was thinking to do the 100000 Ks. service myself but now...)

My car is a 1999 S2 Stagea RS4V usually I run 10 psi of boost now I put it down to 7psi.(BTW miss wants to kill me for play with the boost) and I just put Motul 4100 (I know CHeap ass of me)around 1000 Ks ago...

Link to comment
https://www.sau.com.au/forums/topic/335003-think-my-turbo-is-dying/
Share on other sites
southern_tango Proficient

southern_tango

Posted
  • Author
Posted

Not really after the oil change ,I did it about a month ago or a bit more(Old stuff was black and Thick) and replaced it with Motul turbolight 4100 10W40 and RYCO Z442 oil filter...

Now it happens when the car is cold ,if I accelerate a couple of times it goes away but still there a bit...

scotty nm35 Grand Master

scotty nm35

Posted
Posted

If its not boosting it could be the wastegate but it should still boost up high in the revs. Im thinking its the bearings are shagged. Have you tried tightening all the manifold nuts?

The best fix may just be a garrett one. :down:

Daleo Grand Master

Daleo

Posted
Posted
Checked my oil and it's a bit black not as golden as when i put it...Is that bad or common?(Changed oil in my cars before but never checked the color after...)

The oil's job is to suspend all of the contaminants in your engine, this is why oil goes black. If it doesn't go black it isn't working.

SMOKEYV35 Mentor

SMOKEYV35

Posted
Posted

usually a signal that the bearings in the turbo are cactus. the shaft has excessive play or float allowing the blades of the impeller to rub against the housing. only way to confirm this will be to pull the intake off the front of the turbo and give it a little wiggle (obviously with the car off!). a tiny bit of movement is normal, but anything significant is a problem.

_Ryan_ Grand Master

_Ryan_

Posted
Posted
Checked my oil and it's a bit black not as golden as when i put it...Is that bad or common?(Changed oil in my cars before but never checked the color after...)

Start reading here... linky

the whole page wouldnt hurt :D

Check oil level, check gaskets, check for vaccum leaks, check oil lines to the turbo.

Go to a mechanic.

southern_tango Proficient

southern_tango

Posted
  • Author
Posted (edited)

Today I took the intake pipping to check if there was any play in the turbo's shaft and found nearly no play just a 1/2 mm. back and for but nothing sideways...

So,no smoke ,no oil leak *to the ouside of the turbo and no play just teh bloody metallic noice ...

*found some oil inside the pipping that goes to the SMIC and the pipping going to the throttle ,is that normal?

Edited by southern_tango
scotty nm35 Grand Master

scotty nm35

Posted
Posted
Thanks,Scott,but the bloody thing omly happens when it's cold :D ...after a while sounds normal :nyaanyaa:

Perhaps the turbine is rubbing until the housing expands with heat. It might be a simple as re centering the exhaust side, gives you a chance to check out the bearings while you're there...

southern_tango Proficient

southern_tango

Posted
  • Author
Posted

Think you may be right in this one,thinking about it when i put the dump pipe , forced a bit to make it fit ...guess now it could had damage something with the time...need to go to a mechanic ...but i'm lazy :thumbsup: ,with little time and money :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...