Jump to content
SAU Community

Recommended Posts

hey, my r32 makes a friggin loud couple of knocks when i start my motor when its cold or been sitting for over an hour...

its like

knock, knock knock knock every 0.5 secs.... and gets softer in 5 seconds and goes away after abt 7 secs

is it normal??? or bad and causing damage......

thanks guys :blink:

Link to comment
https://www.sau.com.au/forums/topic/335499-loud-knock-when-starting/
Share on other sites

Is it a knock sound or a kind of a tick sound?

if it's a ticking, it might just be the lifters, in which case it's not really an issue.

possibly having a recording would help, as well some supporting info (how long has it done this? have you changed anything recently?)

done a few km's?, hard life etc

Sounds like big end bearing(s) (rod knock), especially before oil pressure builds up.

Rebuild down the track, or a rod may go out the side one day...

That is one possible cause......

big end??? !@#$

lol, umm the car (4wd system etc) has done 184k kms...

the motor was swapped, and im sure has only had 60k-80k kms...

ill get a recording when i get home on monday.

if its a tick its a really loud tick...

its allways had a slight tick on cold start or after its been sitting for a bit... but after its last few outings its gotten a bit louder.

i ran around the motor with a screwdriver held against my ear and either the injectors are really loud or the lifters have a big gap.

- Max

yeah the injectors are fairly noisy... all the time, this noise is only for like 7 seconds or less at startup...

waterpump sounds possible... but wouldnt it be more of a crunching instead of a knock/tick?

thanks our12 ill check that this arvo and might pull my cam covers off and check the lifter gaps and check for dirty oil

yeah, its a fairly hollow-ish knock.... like amplified injectors.... REALLY amplified... will get audio on monday

I have the same with my r32. But my engines rb20e im not sure what it is either asked a few people know one knows what it is.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...