Jump to content
SAU Community

Front Left And Front Right Ride Height Not The Same.. Why?

snozzle
 Share

Recommended Posts

snozzle Mentor

snozzle

Posted
Posted (edited)

hi all

wanted to lower my car recently (height and damper adjustable coilovers) and have i noticed that my car is actually on a slight slant by roughly 1.5cm's

drivers side is 1.5cm higher than the passenger side

thought my coilovers were stuffed so i took them out, put my stock suspension in and car was still on a slant, but the slant was even more, about a whole inch (driver side kinda looked abnormally high)

put coilovers back on, made sure they were same height spring tension etc, they were both exactly the same, i even swapped sides

still...... same!

so then i took both upper control arms off, found that the driver side one was bent, strange as it sounds i was happy to find this as i thought it meant i found the problem, replaced it with one that was not bent - still same problem!

i then adjusted the spring tension down by 1cm on the driver side, and increased the spring tension on the passenger side by 1cm to see if it would even out, but it didnt however i think the passenger side did lift up a tad

its almost asif the driver side wont go any lower?

so now im lost as to what to check/fix/etc and need more advice

cheers!

Edited by snozzle
snozzle Mentor

snozzle

Posted
  • Author
Posted

pretty sure it hasnt, ive got abit of experience with smashed cars and it definetely doesnt look like it, the wheel may have hit something but chassis wise the car hasnt been damaged/chopped up/welded etc

just_matt Explorer

just_matt

Posted
Posted

Are the suspension bushes binding up?

If the bolts that pass through bushes were done up tight when the wheel was off the ground the bushes may not allow the control arms etc to swing upwards enough to allow the vehicle to sit right.

You could try loosening and re-tightening all bolts that go through rubber bushes (while the vehicle is on the ground).

snozzle Mentor

snozzle

Posted
  • Author
Posted

yeah i did up both sides bolts very tight then nipped them up slightly with a breaker bar haha but still, y would only 1 side do it? i tighted both sides up the same

maybe i should put some grease on the contact spots

just_matt Explorer

just_matt

Posted
Posted

You could try raising the vehicle, loosen all bolts for rubber bushes enough so they can twist, lower the vehicle completely (weight on all wheels), check ride height Left and Right.

If all bolts/nuts for your suspension bushes are slightly loose and it still sits wrong, then atleast you have eliminated a possibility.

Its not how tight you have done the bushes up, but the angle of the control arm when you tightened them up, compared to the angle of the control arm when the wheel is loaded with weight.

One may twist more due to softer rubber, age, cracks etc...

snozzle Mentor

snozzle

Posted
  • Author
Posted

well the base height is already at the minimum coz these coilovers came out of my old car (r34 gt-t) - only way i can dump it more is take spring tension off or possibly order in different springs from BC racing

i dont feel good about masking up a structural problem so i wouldnt do that anyway even if i could, ive booked it into a suspension joint for tuesday but i wanna see if anyone has anymore tips on wat else i could try

i have a feeling i will have to measure up the chassis :nyaanyaa: if its bent around the strut top area ill get it straightened out next year when the motor comes out (if build plans dont change)

its just odd because i dont suspect anything is wrong with the chassis, its a really straight car, underbody is very straight, clean and all original

blind_elk Grand Master

blind_elk

Posted
Posted
...only way i can dump it more is take spring tension off ...
That will RAISE the ride height.

I vote for a twisted chassis. Wouldn't take much of a twist to introduce a 1.5cm discrepancy over the diagonal of the chassis.

I'd get the car corner weighted to work out where the problem lies.

siamak Apprentice

siamak

Posted
Posted (edited)

Erm, by dropping the pre tension on the spring it definetely sits the car lower...?

Ive been looking at the car abit more today looking for irregularities and the 90 degree bend in the sway bar sits slightly closer to the cross member that the other side but my dad rekons sway bars are almost never symmetrical anyway so its not very informative to go by that, ill try get some pictures up tonight though.

Keep the suggestions comming guys, much appreciated!

edit: woops i accidently posted from my mates account, using his pc

cheers

snozzle

Edited by siamak
snozzle Mentor

snozzle

Posted
  • Author
Posted

borrowed my panel beaters "is it square" tool and engine bay from the top is 100% square, doesnt quite rule the bottom side out though i know but i wanted to see anyway lol

took some pics to show the difference in ride height - i dont wanna go any lower than the passenger side, happy with that.. but the driver side is too high and just wont goo downn lol

driverside_high.jpg passengerside_low.jpg

will get some more photos of suspension components tomorrow if i get time

cheers

blind_elk Grand Master

blind_elk

Posted
Posted
Erm, by dropping the pre tension on the spring it definetely sits the car lower...?

Ive been looking at the car abit more today looking for irregularities and the 90 degree bend in the sway bar sits slightly closer to the cross member that the other side but my dad rekons sway bars are almost never symmetrical anyway so its not very informative to go by that, ill try get some pictures up tonight though.

Keep the suggestions comming guys, much appreciated!

edit: woops i accidently posted from my mates account, using his pc

cheers

snozzle

Try it with the sway bar disconnected at the link pins. If the sway bar is loaded up on one side, then it could cause what you are experiencing.

Is the surface you are measuring on absolutely dead flat?

snozzle Mentor

snozzle

Posted
  • Author
Posted

Im going to take the sway bar off completely today.

Yeah, no matter where i am, drive side front is always atleast 2cm or so higher than the passenger side. Definitely not the surface im parked on. Very annoying :D

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...