Jump to content
SAU Community

Recommended Posts

  • Replies 119
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 months later...

Hi ho Hi ho....its off to Willal I go...

Jumped in my car yesterday after having driven it 1/2 an hour earlier with no hint of what was to come.

Started it, shift to reverse, dash lights up like a Christmas tree with faults and throttle input does nothing...car wont move.

AWD system fault light is on (see top right below) along with check engine light.

trans1.jpg

Plugged in my Access Port and found code P0847

trans2.jpg

Had a look at the GTR service manual...code is the following...

trans3.png

Shit....doesn't sound good

Called Martin at Willall....common problem, factory pressure sensors shit themselves. There are 3 in the transmission and are not accessible.

Needs trans/diff removal and transmission disassembly to repair. I have my suspicions that the sensor is actually OK and the pressure is in fact low from a blown seal.

What pisses me off is that this failure has nothing to do with any mods to the car...it happens to bone stock R35s. If my car was stock I could take it to Nissan and they would replace the complete transmission under warranty.

So, car is being shipped to Willal on Friday...while the trans is out will do some bullet proofing mods.

All going well Im hoping to travel from Adelaide to Melbourne Saturday 2nd Feb, stay the night and have some runs at Heathcote drags on the Sunday (there are a few R35s going for runs). Heathcote allows sub 11 sec passes with no cage...will be good to have a play with different levels of the launch control and better my single pass 10.62 at WSID

This is the first and only fault I have had with the car in 2.5 years and I have absolutely flogged the arse out of this thing....cant complain

Pretty standard failure. Talking to a few of the boys who do some work here on the West coast, they all seem to do it between 25,000-40,000kms. Sounds like you got to the very limit of age / kms before they let go.

'South Side Performance' now do complete plug-and-play sensors for the R35 as it's such a common problem.

They're only $200. Your biggest expense will be labour:

http://www.sspperformance.com/product/gr6-transmission-pressure-sensors-/

hope you can make it to Heathcote Kev

seeing what you can run with mod'd turbos vs my full bolt on stock turbo same day same track will be a great comparison for everyone (including myself) who is on the fence whether to take that next step

great opportunity to upgrade the trans - im still on the fence whether to do this as preventative or wait till something goes wrong

Speedah did you try the Warranty path with Nissan???

Also another thing, what did the 2011 front end conversion set you back??? I'm considering doing this myself with my 2010

Yes, I talked to someone at Macarther Nissan who was very helpful...told him the full story. He explained the proceedure they have to go through to gain approval (from Japan I assume). Short story is the car would be there for a week or two while they diagnose/wait for a decision then I would be charged $600/$700 to then to say they can't help me.

Im not too worried...I would rather put parts in it that dont fail. I was very fortunate that it happned inside my workshop. A week ago I was driving in the Sydney City centre during peak hour...I dont know WTF I would have done if it decided to pack it in there.

Edited by Speedah

hope you can make it to Heathcote Kev

seeing what you can run with mod'd turbos vs my full bolt on stock turbo same day same track will be a great comparison for everyone (including myself) who is on the fence whether to take that next step

great opportunity to upgrade the trans - im still on the fence whether to do this as preventative or wait till something goes wrong

Ill be there...try and round up as many R35s as you can.

Stock wheels back on for Willal trip no. 2

trans5.jpg

Ready to go. (car has now been delivered to Willal)

trans4.jpg

If you need to transport your car from Wollongong/Sydney area interstate by someone that actually cares Mick is the man. Some of you may be familiar with his 7.4sec Torana MV454

mv454.png

I seriously hate transport companies all together. While I didn't have issues with CEVA, I had a fuel contamination issue a few weeks back and the GTR had to be tray back transported to Moorooka Nissan for draining. I made sure I taped up the front lip (2 layers) just in case it was scratched. Sure enough, the tape was fully scuffed when I picked it up from Nissan the next day. Luckily there was no damage.

The transport used was the GTR Roadside Assist preferred - Wilson Transport - in Brisbane. I do not recommend them, nor will ever use them again!

Edited by Wardski

Have they fixed this pressure sensor problem in the later model R35's?

Nup. Transmissions are almost identical in that regard all the way to 2013. With all GT-R's its not a matter of if it will happen, its more like, when it will happen :P

Edited by Wardski

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...