Jump to content
SAU Community

Pfc Tuning Question

j2fast

By j2fast,
in Engines & Forced Induction

 Share

Recommended Posts

j2fast Enthusiast

j2fast

Posted
Posted

i have for some time been looking at the Dwell ign VS rpms in the PFC for my rb25 motor but i don't know if i should are is it necessary for my motor with mods to mess with it. the mods are t76 turbo, all bolts on, 1000cc injectors, 2 fuel pumps running e85. so i know that timing will need to be up a lil more just from using e85 but don't know much about it. if anyone is an experience tuner with this please shine some light on it for me.

Link to comment
https://www.sau.com.au/forums/topic/336256-pfc-tuning-question/
Share on other sites
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

I personally haven't, but I say on full load, row 16 on your map reads 17 15 13 13 13 13 13 14 14 15, e85 will allow more advanced timing so it "could" be like 21 19 17 17 17 17 17 17 17 118 18 , etc....

you get the ideal.

STATUS Grand Master

STATUS

Posted
Posted
i have for some time been looking at the Dwell ign VS rpms in the PFC for my rb25 motor but i don't know if i should are is it necessary for my motor with mods to mess with it. the mods are t76 turbo, all bolts on, 1000cc injectors, 2 fuel pumps running e85. so i know that timing will need to be up a lil more just from using e85 but don't know much about it. if anyone is an experience tuner with this please shine some light on it for me.

what coils? i have a few good setups.

j2fast Enthusiast

j2fast

Posted
  • Author
Posted
I personally haven't, but I say on full load, row 16 on your map reads 17 15 13 13 13 13 13 14 14 15, e85 will allow more advanced timing so it "could" be like 21 19 17 17 17 17 17 17 17 118 18 , etc....

you get the ideal.

naw on e85 mines like 55 55 55 55 55 48 48 48 42 42 42 40 40 35 with no knock and while i was on the dyno i was gaining hp but i stopped adding cuz i thought that was pretty high

rob82 Mentor

rob82

Posted
Posted
naw on e85 mines like 55 55 55 55 55 48 48 48 42 42 42 40 40 35 with no knock and while i was on the dyno i was gaining hp but i stopped adding cuz i thought that was pretty high

The knock resistance of E85 is quiet high and on most setups you can run virtually whatever ignition curve you want without knock. However there is absolutely no point going further than MBT as you will cause combustion gases to act on everything within the chamber for longer. E85 tuning really needs to be done on the dyno to find MBT.

paulr33 Grand Master

paulr33

Posted
Posted

MBT(Minimum advance Best for Torque)

The ideal ignition timing to produce maximum torque for a given load and engine RPM. Applying this value for every stage would be extremely efficient and minimize load on the engine while driving.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...