Jump to content
SAU Community

Recommended Posts

Hi Guys,

I am about to pull the engine out of my 94' BNR32. Basically I am looking for some advice as to what I have missed given that I am only seeking 250-280rwkw (ands thats in the future not now). I am primarily looking for reliability atm.

So here is what I have:

-water pump

-gates timing belt and new ilder bearings

-new turbos

-new dump pipes

-new silicon heater hose kit

-bought a full engine gasket kit so I can do the gaskets for the plenum.

I think I should get a sump baffle whilst the engine is out. I just cannot decide what one! I have been looking at the tomei one that fits in the standard sump.

Thanks for your input guys.

Link to comment
https://www.sau.com.au/forums/topic/336830-what-have-i-missed/
Share on other sites

If you only want 280rwkw then you don't need to change dumps, sump mods.

Also be careful when changing the plenum gasket. I do believe there is a "trick" to get it to seal correctly. Do not clean the butterflies etc either.

Also the silicone heater stuff I've found to be crap. I've had to replace 3 hoses in 1.5years and I've done less than 10,000kms.

It's one of your typical EBAY special's. It's been replaced this time though with Nissan OEM hose :geek:

Cheers Ash - I have a pretty good mechanic, one I actually used to work for at revo, but we'll definately be careful on the plenum. I have heard that the standard gaskets can become very brittle as they age and have a tendency to split (CRD and JustJap told me).

I got a very good price on the dumps so thought I might as well pick them up now - who knows what will come in years to come?

Also cheers on the heads up re silicon hoses - is the issue that they perish quickly or that they cannot handle heat? Any incites?

Yep - they do fail, and just as much of a pain to replace so good thing to do if the motor is out.

Also get the paint tidy'd up as well :geek:

Fair enough if you got a good price :D

I kept getting pin hole leaks which then results in coolant being sprayed all over the place.

From what i could tell the hoses are a bit thinner, and there isn't a lot of the webbing inbetween the silicone layers when you slice it open.

So obviously lacking support and durability/quality.

3rd time it happened it was the straw for me so went with OEM hose that was modded to suit.

Oh most definately the paint is going to get a tidy up :geek: one of the reasons of buying a full gaskit kit is I can paint all the parts properly. But as it is not a genuine reliability mod I didnt think to post it :D

Why are you pulling the engine out? How many km has it done? If you're going to take the sump off (and the head?) you may as well do rings and bearings. Replace and correctly torque the tensioner bolt when you do the cam belt etc.

Why are you pulling the engine out? How many km has it done? If you're going to take the sump off (and the head?) you may as well do rings and bearings. Replace and correctly torque the tensioner bolt when you do the cam belt etc.

Honestly, who knows how many Kms their car has done!? The engine is coming out for a few reasons. Firstly, as stated above I am doing my turbos and from the advice I have received from many people is it is just as quick to pull the engine and do them out of car. Secondly, I wanted to do the heater hoses and the vaccum lines for the engine - basically undoable with the engine in place. My gearbox is making some interesting noises which make me think the input bearing is a bit dodgey so I want to overhaul it as well. Its easy to service out of car.

Regarding doing the bearings and rings. Hmmm... The engine compression is good and it isnt using any oil. I am not planning on building a power monster so i cannot justify opening it up to that extent. Lastly and most importantly, the age old question - where do I stop? If I did the rings and bearings, I most likely couldnt justify the hassle of doing it without new throwing in some forged slugs. Then, if I am doing that should I hone the block, check the crank, have the head once overed, etc.... Basically not what I am aiming for atm.

Yeah the machining costs add up - which inevitably means you want to put the best parts in to make the most of it... luckily I'm not going down that route just yet :D

Ye the age old "where do you stop" is certainly real :whistling:

You'd be @ 4k before you began, then no point going those turbos... AFM changes, injectors and suddenly 10k+ has walked out the door!

Ripping the motor to do what you wanna do - is very ideal and smart.

Plenum & hoses are a pain in the ass and much easier outside the car as are turbos.

Overall cost would IMO, be cheaper labour wise as it doesnt take that long to get the motors in/out with experienced people.

Luckily my labour cost is $0 :whistling: Allows more parts to be bought. Ash - do you reckon the tomei sump baffle is worthwhile? I dont think I need to go to a larger winged sump, but as I might track it in the future the sump baffle is needed?

Honestly having seen cars running sticky rubber and a lot more power than you - they all did it stock sumps and 1litre overfilled.

So I'd say no. But it's your call but without doing the other head/oil mods etc, that's where the real problems are anyway

I have kinda been scared about putting an N1 pump on from the horror stories (i know many people have had success as well). I wasnt going to do an oil restrictor as I wasnt planning on cracking the engine open.

Does the N1 provide higher pressure / greater L/min?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...