Jump to content
SAU Community

Recommended Posts

Is it worth stroking a 25 to 2.7 with the 26 crank rods pistons and etc or would it be more feasible to just build a 26?

What would be the advantages and disadvantages using the 25?

Car is a 32 sedan and will hopefully be used for a bit of circuit and road use.

Am open to all advice. AAANNNNDDDD GO...

Link to comment
https://www.sau.com.au/forums/topic/337080-is-it-worth-stroking/
Share on other sites

stroked 2.7 RB25 would be good, but remember (unless you use a neo 34 head) it's still gonna have hydraulic lifters, and wont be as rev happy/efficient as a 26 head.

That said both options make great power, there's really nothing to win one over the other...

considered a 26/30 or 25/30?

stroked 2.7 RB25 would be good, but remember (unless you use a neo 34 head) it's still gonna have hydraulic lifters, and wont be as rev happy/efficient as a 26 head.

That said both options make great power, there's really nothing to win one over the other...

considered a 26/30 or 25/30?

Mine revs to 9000rpm, hydraulic lifters and Tomei springs :dry:

Mine revs to 9000rpm, hydraulic lifters and Tomei springs :dry:

Hmm fair enough!

I stand corrected :D

That is sorta true as a general rule though right? Solid lifters are more efficient and more rev happy than hydraulic types?

Hmm fair enough!

I stand corrected :dry:

That is sorta true as a general rule though right? Solid lifters are more efficient and more rev happy than hydraulic types?

Yes, and you can get a solid lifter conversion kit to make the RB25's solid, like the Neo's, but for the cost it wasn't worth it. Instead we opted for the valve springs, and hasn't missed a beat. To be honest those, on most engine setups I've seen the engine is out of efficiency before 9k.

I've considered a couple of combos but for me the 2.7 stands out a little more because its different. The donor motor is a 33 series 1 as far as i can tell. The combo i'm looking at is

34 crank

nitto rods

JE Pistons

nitto oil pump

272 cams with springs

sard 750's

gt35 with 6 boobs and whateva else is required

rb30 bottom end is hard to pass up, alot cheaper than stroking the rb25 and if anything stupid goes wrong the bottom end is alot easier to replace. Wont need such a large duration cam as youll have more torque earlier and wont need to revv as much... i find my gt35r is still a bit laggy for my liking on the 3litre, but heaps better than the 25.. a good 700rpm, if you can wait until the end of the year ill have mine rebuilt and back on the road.. can take you for a spin and see if you like it.

Jarrod

+1 for the 30DET, you're rebuilding anyway so go splash $100 on an RB30E, buy pistons and rods to suit and longnose the crank, use your 25 head and the cams you were planning on. Go the GT35R with .82 (minimum) or 1.06 housing.

If you go the 30 make sure you let Kyle know it's a 30 in a 32gtst so the manifold will fit. He'll also want you to get a 50mm gate.

Bart, have you got a VQ in a car in your shop? will call past and have a sticky beak if you do

And Bubba by longnose the crank is that the collar you stick on it to suit the oil pump?

Edited by turboedsloth

Yeah I mean put a crank collar on so you have the long oil pump drive like 33/34gtr cranks.

Personally I'm welding the snout of my crank and machining back to suit my specific gears as opposed to using a generic collar that's toleranced to suit a variety of gears. Some people don't like the idea of welding the crank though so it's an each to their own thing. The reason I'm going down that path is that I firmly believe the common destruction of gears is due to the poor tolerancing between drive and gears.

i have the 0.82 exhaust housing on the gt35r

i quite like your idea there bubba.. i had a crank collar fitted on my car and my oil pump failed in a very strange way... the outside gear ended up in about 10 bits, i am hoping to rectify the problem with a better balance, harmonic balancer and a billet pump, i might have to check the clearance between the collar and the pump.. one of the engineers i took my pump to said it looked like there wasnt enough clearance axially for the gears.

Jarrod

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...