Jump to content
SAU Community

Recommended Posts

Hey guys...

I am an avid reader of the performance section of these forums but i find that most people serching for more RWKW's rather seconds...

My question is what would be needed to be done to a stock R33 GTS-t to produce 11's, with street tyres, and no MAJOR weight reduction.

I am looking to purchase a 33 very soon and wanting to work it acheive 12 sec 1/4's but just got curious as to what extra would be needed. I also intend on this to be a daily driver with bite.

(BTW I am aware that there are multiple ways for this to be acheived, just looking for the different methods and ideas)

Cheers

Link to comment
https://www.sau.com.au/forums/topic/33712-what-is-needed-for-11-sec-14/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Money.

Sorry, couldn't resist it.....

We have a full weight R34 GTT that does 11.7with 310 rwkw on Nitto radials. So do a search for how to get 300 rwkw out of an RB25DET. There would be at least 50 that I have posted to. Take your pick of methods and then stick a pair of Nittos on the back and, as long as you can drive, and the track is is good condition, an 11 is achievable.

Hope that helps

Try and do it with the stock turbo :D.

I'd be looking at BFG drag radials tyres wise and a good working over of the suspension. With BFG's you should get the 60ft down to high 1.5's / low 1.6's (like to see that out of sh*tto's). A modifed transbraked Turbo 350 auto with a 5000rpm high stall and a lower diff ratio might help too.

Hi rev, Wilson did a 1.45 on Nittos, Munroe did a 1.48 and Lee did a 1.6. I've got plenty more examples if you like. None of those were in Perth though, in fact I can't find any decent radial tyre times from Perth. Must be the track.

Just make sure you try and buy one with the basics already covered, otherwise it'll add up to "may as well just get a GTR" territory.

If you can find one with FMIC, full exhaust, boost controller, suspension, aftermarket ECU, and hopefully a few other extras for around $20k, that might save you $10k just there. That might make a budget of getting there below 35k possible.

Then your concerns will be building the internal strength of the motor, turbo and the required support systems for that. Otherwise, yeah, just find one already done .. it may be boring but it will save you a **** load of money.. over the last year or so I've seen quite a few GTS-T that will do mid-12's for $25-30k

Yeah i spose i never thought of that.

I am a huge fan of the GTS-t as a quick but non-expensive car and also has the looks. The main reason i was after a GTS-t was the rear wheel drive aspect. How hard is it to turn a GTR into rear wheel drive?

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
×
×
  • Create New...