Jump to content
SAU Community

Recommended Posts

open your boot up, and on the top close to where the hinges are, you will see a rubber plug where your wires run out from, one on the left and right, they are kind of rubber plugs. pop them out, and under that if you have a factory connected spoiler there should be 2 screws under there, one right one left and the middle of the spoiler should be glued on with a special rubber glue, kind of like liquid nails, just not as strong.

Link to comment
https://www.sau.com.au/forums/topic/337582-spoiler/#findComment-5457247
Share on other sites

Just had a look at the Pics, doesn't look like any spoiler, just the normal back. Someone help him out, mines got some sort of spoiler on it, so its not the same.

sorry, trying to fit one ,they have the black clips were the top part of the boot opens and the spoiler sits in there just didnt want to snap them of if there was a easy way ?

Link to comment
https://www.sau.com.au/forums/topic/337582-spoiler/#findComment-5459428
Share on other sites

sorry, trying to fit one ,they have the black clips were the top part of the boot opens and the spoiler sits in there just didnt want to snap them of if there was a easy way ?

Looking at the fast diagram, there are deffinatley 2 nuts that hold that plastic trim in place that go through the top of the tail gate. Not sure how to get at them but they are there.

Cheers

Andy

Link to comment
https://www.sau.com.au/forums/topic/337582-spoiler/#findComment-5459464
Share on other sites

Talking M35 or C34? Might help before you start going for non existent screws... :O

took me a week to work out what a c34 stood for or whether the questions were relevant to M35s when i first joined. (but its a steep learning curve)

Hence why i start my threads or questions with M35 in the subject matter.

The problem is when people dont mention what its in reference to you usually gotta refer to what cars they own in their avatar...can be a double edged sword though if theyve got a C34 and a M35!

"Well on my C34!"

heehe :huh:

Link to comment
https://www.sau.com.au/forums/topic/337582-spoiler/#findComment-5462467
Share on other sites

so got the paint for my spoiler silver KYO there are 5 different shads of paint Got it on the flip card its so hard they all look the same how can there be 5 different colors for the same code KYO ?

If it makes a difference, I think you will find that the code is KY0 (as in "Zero", not the letter "O"). Dunno if it will narrow it down for you though.

Edited by iamhe77
Link to comment
https://www.sau.com.au/forums/topic/337582-spoiler/#findComment-5465655
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...