Jump to content
SAU Community

Recommended Posts

I bought this last friday, to replace my impreza, which will fund a work ute

its clean as, auto :-( , and a tight and responsive L24e $850 with 2 months rego

I have 2 5 speeds and a spare L24e from a C210. I was wondering if anyone has

everything else to convert to manual (pedal box, clutch master and line, stick,

console rubber and floorpan seal) and if the yoke is the same with auto and manual

feels good to be back in a skyline, any help is appreciated

post-60300-1285230926_thumb.jpg

post-60300-1285231071_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/337928-my-new-daily-drive/
Share on other sites

damn.

thanks guys for your help

there is a datsun wreckers in Castlereagh, Sydney, that has a straight C210 coupe

minus engine, gearbox and most of interior if anyone wants it. Has rust in boot, but is worth saving. also 2 MR30 sedans

His name is Carlos, he's a reasonable bloke, have a chat to him

http://www.sportsclassic.com.au/

  • 2 weeks later...

^^^ Carlos Casmiri ^^^ Rally dude and hoarder of Zed Parts.

You need the tailshaft and speedo cable from the manual, as well as the clutch pedal and the bolt/rod thing that goes through the manual pedal box...

I reckon that, the Auto and Long Manual box would be the same length (didn't measure) so you might be able to use the Auto Tailshaft with a Long Box... but the gearstick will be a few cm further back in the hole...

Biggest problem is going to be the crossmember... the Auto Tunnel is about 10cm wider than the Manual Tunnel, so you are trying to bolt the gearbox crossmember into thin air... Auto one crosses the transmission in a completely different spot, and bolts through the floorpan at different levels, so you will have a slight complex fabrication job...

Cheers,

Daewoo

^^^ Carlos Casmiri ^^^ Rally dude and hoarder of Zed Parts.

heeheehee i like that

You need the tailshaft and speedo cable from the manual, as well as the clutch pedal and the bolt/rod thing that goes through the manual pedal box...

Im hoping to find a complete manual at the wreckers. nothing in sydney, goulburn has a couple of auto's. i will find one!

I reckon that, the Auto and Long Manual box would be the same length (didn't measure) so you might be able to use the Auto Tailshaft with a Long Box... but the gearstick will be a few cm further back in the hole...

thought that would be the case with the long box, so i wont use this option.

Biggest problem is going to be the crossmember... the Auto Tunnel is about 10cm wider than the Manual Tunnel, so you are trying to bolt the gearbox crossmember into thin air... Auto one crosses the transmission in a completely different spot, and bolts through the floorpan at different levels, so you will have a slight complex fabrication job...

Ill be able to fabricate the crossmember no worries. I think my biggest drama will be getting hold of the complete conversion.

This is all very useful info, Thanks daewoo, muchly appreciated!

Ill be able to fabricate the crossmember no worries.

When you do, can I have one :(:rofl::D ... all progress on mine stopped about 3 months ago when I hit this hurdle, and lost interest... as the teachers all said "Daewoo is easily distracted"...

I think my biggest drama will be getting hold of the complete conversion.

Two things... the short boxes are in short supply, only ever used in MR30s and Stanzas... and, the plate that holds the input shaft bearing (or whatever it's real name is) is Aluminum, so prone to shitting themself... before I bought it, I would be taking that plate off and seeing if it is faxed, if it is, the plate is the same as a 'K' box, but it usually faxes the whole front housing (which you can also just swap for a 'K' one)...

As it is just a Daily, probably not a big deal...

Cheers,

Daewoo

Edited by Daewoo
Im hoping to find a complete manual at the wreckers. nothing in sydney, goulburn has a couple of auto's. i will find one!

Rushy (Pick n Payless) at Blacktown doesn't have any ?????????

Take a drive down to Dapto Pick a Part, they have 5 MR30's down there and I think 2 were manuals complete when I was there last Thursday.

I wasn't looking for manuals persay, but will if you like as I should be down there this week after picking up my manifold from a guy nearby. (Extreme Turbo Manifolds)

Cheers, D

Dapto don't know what they have!

Last Thursday they told me they had ONE (1) but I found FIVE (5) so maybe the four (4) they don't have are manual lol

I'm going back to Extreme Turbo Manifolds on Thursday morning, so I will stop in to Pick a Part and look. If I find I'll take some pickies for you as proof.

Cheers, D

Ok! Been to Dapto today and as usual, they don't know what they have and there was one manual, but the pedal box was being removed when I was there and the rest had gone, if the guys taking out the pedal box already didn't have it.

PM me with what you need for this manual conversion and I'll see what I have spare.

Cheers, Dennis

thanks for that ghostrider. wreckers people are generally pretty dumb, like the guys in Melbourne,

crushed the C210 coupe after having it for only a week and everyone wanting stuff off it

Mag86, i need the whole lot, seeing as the C210 5 speed is too long

Do R32 gtst's use a stubby box? i know is a lot smaller than the R33 box.

had a thought, RB25 n/a and a R32 box. what do you guys think?

Also bought a DR30 series 2 instrument panel, techo goes to 9000!

but all the connections are different to the stock instrument panel.

ill upload a pic asap

thanks for that ghostrider. wreckers people are generally pretty dumb, like the guys in Melbourne,

crushed the C210 coupe after having it for only a week and everyone wanting stuff off it

Mag86, i need the whole lot, seeing as the C210 5 speed is too long

Do R32 gtst's use a stubby box? i know is a lot smaller than the R33 box.

had a thought, RB25 n/a and a R32 box. what do you guys think?

Also bought a DR30 series 2 instrument panel, techo goes to 9000!

but all the connections are different to the stock instrument panel.

ill upload a pic asap

Your going to have a problem fitting your S2 instrument cluster into an S1 car. All your connections are diferrent, so you're going to have to rewire or maybe replace the instrument loom. Don't know if the latter is possible, but rewiring would be.

The R32 box can be used but it needs an L series front housing on it. As Mags says Stewart Wilkins will do the mod for you. The gear lever is going to come out of the tunnel a little further back in the hole, which isn't a huge biggie issue.

I was originally going down the RB25DE conversion until I stumbled across my PNV and decided to keep it a bit stockish. It's a relatively easy conversion and been done to bits, along with the RB30E conversion.

I'm about to have a huge cleanout of accumulated bits, so if your interested let me know.

Cheers, D

This is what you want if your going to do it easy!

http://cgi.ebay.com.au/Nissan-DR30-Skyline...=item58867ab14f

If you buy this, take it to South West Instruments at Smeaton Grange and he will modify it for you. He did my S2 cluster a few years ago.

Cheers, D

post-2962-1286522073_thumb.jpg

Yo! here is my instrument cluster

post-60300-1286533497_thumb.jpg

post-60300-1286533432_thumb.jpg

I like how yours goes to 260km/h. ill think about that one

that cluster itself will justify a engine transplant :-)

The series 2 dash KILLS the series 1 dash!

thanks andrew, good info!

engine exchange isnt a huge priority at the moment

might do it in 6 months or so

ghostrider, when you do your clean out, if you can gather a

complete 5 speed conversion, including tailshaft,

and also series 1 hotplates in good condition. If you have

all this, and we can talk price.

thankfully, you dont live too far from me

I read somewhere that for ideal air supply, the plenum

volume is matched with engine displacement, and double engine

displacement for n/a engines. cut 3 sides off the stock plenum

smoothen the inlet runners and tig up a 2.4l volume plenum.

dont know if im dreaming now, but a RB30 throttle body and airflow meter

to a aftermarket ecu?

The 260km/h speedo is very difficult to get these days, as Jenesis wont trade outside of the domestic market. One sold on ebay (complete cluster) recently for a little over $200.00 and the Tomei variety 240km/h gets onto Yahoo in Japan a bit often but landed it would cost in excess of $600.00.

When you look at the back of the S1 cluster, you will find it entirely diferrent to the S2.

I might have an Aussie S2 dashboard harness in a grey dash under the house that you can play with if you like. I'll have a look over the weekend and let you know.

Mechanical parts I will be reluctant to let go because I have 2 x KHR30 Paul Newman coupes & an DR30 coupe track car that need maintaining. A stock tailshaft I might have, as I'm upgrading one of my PNV's to the stronger larger DR30 tailshaft. The companion flange might be an issue because all my R30's came out with R200 diffs.

Probably the only box I have that I would be prepared to let go is an HR31 RB20DET box.

The RB30E throttle body isn't much better than the one you have now. The next one up is the 60mm KA24E (U12 Pintara) or RB25DE throttle body and with an a/mkt ECU you wont need an AFM at all, as it will most likely use an MAF sensor.

As for an inlet plenum, you might find it's more cost effective to extrude hone or power port the manifold. I have an N42 (non EGR) 280ZX inlet manifold that has been comcoated, that I might be tempted to part with, or maybe a stock 280ZX EGR manifold, depending how your bent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...