Jump to content
SAU Community

R33 Help

Kenna802

By Kenna802,
in Engines & Forced Induction

 Share

Recommended Posts

Kenna802 Experienced

Kenna802

Posted
Posted

hi all,

this is what i have got rb33 series 2 with new plugs new coils, return fmic, full 3 inch s/steel exhaust, running 12 psi with ecu tuned by toshi and and a gen walbro fuel pump. ( had car all serviced and radiator, water pump, fuel filter timing belt etc all replaced) now power is about 190 atw and i want about 260-270 atw

should i upgrade ecu, injectors, and turbo/hiflow my budget is 2-3 grand is this possible? any ideas would be helpful i would like your ideas no matter how little they may be thanks

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/
Share on other sites
t_revz Grand Master

t_revz

Posted
Posted

GCG highflow is around 1700-1800. not sure bout hypergear. maybe get highflow and ecu and run on the limits of the AFM until you have the coin to get a Z32 and injectors as AFM will run out of legs before the injectors

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/#findComment-5466724
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

For $2000-$3000 - No.

Injectors are $700-800, ECU + tune is at least $1500.

$2300 before you even start with the turbo, fitting, new dump etc. Then comes the clutch and everything else.

You need at least 5k realistically maybe more.

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/#findComment-5466730
Share on other sites
GeorgesR34 Collaborator

GeorgesR34

Posted
Posted
hi all,

this is what i have got rb33 series 2 with new plugs new coils, return fmic, full 3 inch s/steel exhaust, running 12 psi with ecu tuned by toshi and and a gen walbro fuel pump. ( had car all serviced and radiator, water pump, fuel filter timing belt etc all replaced) now power is about 190 atw and i want about 260-270 atw

should i upgrade ecu, injectors, and turbo/hiflow my budget is 2-3 grand is this possible? any ideas would be helpful i would like your ideas no matter how little they may be thanks

For 2~3 Grand you can get a GT3076R in the new nissan 6 bolt housing. (I think they were for $2300). Or get hypergear to do your high flow, they can make your stockie to pump 300rwkws+. Check their thread out.

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/#findComment-5466945
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted
For 2~3 Grand you can get a GT3076R in the new nissan 6 bolt housing. (I think they were for $2300). Or get hypergear to do your high flow, they can make your stockie to pump 300rwkws+. Check their thread out.

Not one supporting mod listed there. What good is a turbo if you have no other parts to make use of it?

As i said - its a good 5k adventure.

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/#findComment-5467072
Share on other sites
lav Community Regular

lav

Posted
Posted

Stock GTR 33 Series 1 with below mods.

- Exhaust (High Flow) $200

- PFC (Second hand) $950

- Cam Gears (by Racepace) $350

- Tune $600

With above mods, went from 194kW to 264.5kW

All for $2100.

Everything else on the car is stock (Turbo/Engine)...

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/#findComment-5467601
Share on other sites
gotRICE? Veteran

gotRICE?

Posted
Posted
For 2~3 Grand you can get a GT3076R in the new nissan 6 bolt housing. (I think they were for $2300). Or get hypergear to do your high flow, they can make your stockie to pump 300rwkws+. Check their thread out.

I had a look at that, and was wondering how it fit, as as far as im aware, the GT30R needs a 10mm spacer to clear everything on an RB20/25 with a stock manifold.

How'd they get around that one?

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/#findComment-5467855
Share on other sites
GeorgesR34 Collaborator

GeorgesR34

Posted
Posted
I had a look at that, and was wondering how it fit, as as far as im aware, the GT30R needs a 10mm spacer to clear everything on an RB20/25 with a stock manifold.

How'd they get around that one?

Mine was a factory OP6 high flow, every thing bolted back the way it was. the 300rwkws+ high flow I referred to was the so called "pu high flow" which comes with a .82 OEM pattened turbine end. From photos all it needed was a oil feeding line like all their other high flows. It runs on factory comp housing so I guess spacer is not needed. Have a read in their thread, lots of information:

http://www.skylinesaustralia.com/forums/Hy...ce-t261613.html

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/#findComment-5470036
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Whilst it makes 300rwkw, the power band is not that of say a GT30 which has a good 1000rpm extra to play with.

Horses for courses i guess and many factors one must consider when purchasing a turbo.

Yeah a turbo might make "X" power, but the real point is just how it makes that power. Is it responsive, how much RPM do you have to work with etc.

Link to comment
https://www.sau.com.au/forums/topic/338248-r33-help/#findComment-5470050
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • Duncan
      Unpeeling the Orange

      By Duncan · Posted

      That's my life. Past-Duncan has a lot to answer for
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Yep four point harness. Mounted to a bolted in brace running behind the seats. Dont use it for daily driving tbh but good to have for when its needed plus it looks cool.
    • Peeeeetaaah
      R34 Gtt Wheel Offset Advice

      By Peeeeetaaah · Posted

      I had to double check the thread title r34 gtt offset advice lol. Thought maybe i posted on the wrong thread. 😂
×
×
  • Create New...