Jump to content
SAU Community

Recommended Posts

  • Replies 172
  • Created
  • Last Reply

Top Posters In This Topic

floor mats sold

grill sold

front blinkers/ fog lights sold

front and rear bar sold pending payment

ac compressor sold pending payment

Edited by Goodo

how much can you do the drivers side door shipped to 4226 qld?

if your anywhere near syd or canberra on the 8th or 9th of nov i'll take it off your hands

does it have the stock 17's on it?

if so, how much are you after?

how about some m35 17's ( 235 x 45 x 8.5)

with slight curb rash!

with some japanese autogaurd tyres ... $100 plus postage

what steering wheel you got mate? if its momo, i'll almost definately take it, even if its just the normal type as long as its in good condition i might take it... just want an airbag wheel as my new stag has a MOMO jet wheel on it :)

what steering wheel you got mate? if its momo, i'll almost definately take it, even if its just the normal type as long as its in good condition i might take it... just want an airbag wheel as my new stag has a MOMO jet wheel on it :)

I dont have the momo wheel but i do have the standard one in what i would call pretty good nick give me your email address and ill send you a pic

  • 2 weeks later...
Hey. Do you still have the metal clips that hold the rear metal pate on the back of the hood lining. Mine are all broken. Thanks

yeah i will say i would but im not 100% sure which parts you mean if you could take a pic of yours just so i can see what i am looking at thanks nathan

il grab apic when i get a chance but if you open the boot and look at the hood lining there is a metal plate that goes from one side to the other on the back edge just inside the hatch, i need the clips that hold it on and possibly the plate pending if i can straighten mine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...