Jump to content
SAU Community

Recommended Posts

Hey all,

First of all, to be polite my name is Charlie.

Recently I bought a Nissan Skyline R34 GT-T. Everything is stock except I have this mushroom podfilter, catback exhaust and a turbo timer.

Sorry if i dont make sense or miss anything here because this is my first turbo car :). Just got off my Ps yay

Problem:

When driving the car, it looks like it spoofs up really quick than normal and I think the previous owner might of tuned up a little.

Anyways the main problem is that When I push the car hard on the first gear, it would go up to about 600rpm then the power cuts off and nothing else i can do but only to wait for it to go down then I can push again. At the second gear it would go to about 550 rpm and about 500 and so on.

I went to one of the mechanic (Dont know if hes a real pro or not) and he said it is not the rev limiter and he explained that all stock GTT has the rev limiter at 700 rpm to all gears. He said there is something wrong with it. He needs to check it properly. It could also be the wastegate also he said.

Does anyone here has the same problem or know what my problem is? How did you fix it or how can i fix it?

Kindest Regards

Charlie

Link to comment
https://www.sau.com.au/forums/topic/341420-r34-gt-t-power-cuts-off-help/
Share on other sites

thanks to turbos it can be a number of problems, an issue like this its best to go over everything basic to begin with.

1 check your wastegate on your turbo is opening and closing properly, do this by taking off the C clip from the rod and move the arm, make sure its operation is smooth.

2 go over your whole intercooler piping to make sure no leaks and check all the clamps are tight

3 check you have the correct spark plugs gapped correctly also

4 run some injector cleaner through your tank

5 test your coilpacks to see that they are in good working order

6 clean your AFM and check solder points inside it, and make sure the plug is in good condition

7 check the boost your running on a aftermarket boost guage, make sure your running under 10psi

8 check and reset the TPS

9 after all the above, reset ecu

you say it SPOOLS up really quickly? and that its been tuned? if its a stock ecu it cant be tuned, if its spooling up quickly you may have an exhaust leak? (someone will confirm if im correct in saying that) if its over boosting it could be your wastegate which ive noted above. but to me this sounds electronic.

if it's cutting out at 6000rpm (i'm assuming you mean 6000rpm and not 600rpm since it idles at higher than 600rpm) and by cutting out you mean it's sort of like the engine has just turned off and not just spluttering, then i'd say that more than likely the boost is up a bit too high. get an aftermarket boost gauge so you can see exactly what pressure it runs.

if it's cutting out at 6000rpm (i'm assuming you mean 6000rpm and not 600rpm since it idles at higher than 600rpm) and by cutting out you mean it's sort of like the engine has just turned off and not just spluttering, then i'd say that more than likely the boost is up a bit too high. get an aftermarket boost gauge so you can see exactly what pressure it runs.

i think he means it just dies, if it was overboosting id say it would keep revving

i think he means it just dies, if it was overboosting id say it would keep revving

possibly. depends on what sort of cut it is hitting.my 33 used to die when it hit boost cut, but then it would kick back in and keep reving.

if it is really dying until you drop the revs down a fair way then it may be an issue with the AFM dropping it into limp mode. check the ecu for fault codes might be something worth doing.

i had a similar problem which has just been rectified (it might be the same as urs)

basically when i would accelerate hard (if i was just cruising it wouldnt happen but still felt a bit under powered) i would get to arounf 4500 rpm and then the car would stutter really bad or surge (very similar feeling to the traction control kicking in but alot harder)

problem was a fuel pump. just put a new one in and problem is gone.

Thank to all your respond, i really appreciated it.

First of all, yes mad082 im mean 6000 rpm.

I took it to the Mechanic, he checked the computer, test OK (Has been reset as well). Checked fuel crank angle sensor OK, checked in jector pulse OK, checked fuel pressure was low 40psi on full, replaced secondhand fuel pump and rechecked 50psi OK. checked boost controler OK we wll ;)

First i thought it was a traction control as well, but this each time this happens my head almost hit the steering wheel O_o. Pull the car so hard.

I paid $145 for the second hand puel pump and $70 for labour. I still have the problem. :)

@Clutch those steps are reasonable. Ill double check with those when i have time. On top of that i asked a guy who used to have R34 GTT as well, he said he had the same problem and it was the spark plugs. he said go buy 6 of them from Nissan dealer and change them. That was how his GTT got fixed. I still have a high doubt that it will fix by changing those spark plugs. O_o

Kindest Regards

Charlie

Edited by Charlie Bun
what boost pressure are you running? i'm guessing it has something to do with it

How can i check? Sorry i am so noob. :ermm:

But I dont think it is the problem though. As the mechanic said that is has nothing to do with the boost controller.

As i stated earlier today, a dude told me to change spark plugs. Can anyone onfirm with that? because i dont want to pay for nothing again :ermm:

$30 each one of them and plus the labour.

So what do u guys reckon?

you need a boost gauge hooked up to see exactly what pressure its running. dont rely on gauge on dash.

expensive isnt always better. ngk bcpr6es from memory and only couple bucks each

Well i dont know if this is what you are looking for.

This car is fully stock. Something that i know about a stock GTT is that it has not even 1 bar. More like 0.7 of a bar.

Is that what you are looking for?

I really need to meet up with one of you pros. I am so noob at car. Hence: this is my first turbo car

the stock boost on the rb25's is about 7psi (0.5bar).

i just read your post in the AC compressor thread where you said that it cuts out even if you just rev it on the spot in neutral. this rules out it being boost related. this puts it down to being something like the crank angle sensor or AFM or something like that. possibly even ecu related. my advice would be to get a consult cable (google ecutalk) and then you can check the ecu for fault codes (easier than doing it without a consult cable and just counting a flashing light). i'm guessing it will show some errors

Are you in Sydney ? Happy to let you use my consult cable to check for error codes. I reckon it's a faulty AFM or the AFM soldering.

If you have an aftermarket blow off valve, get rid of it and put the factory one back on. New spark plugs are only about $20 for 6.

Once again, thank for the replies. Well the ECU was reset and all error codes had been cleared. The crank angle sensor was checked and it was OK.

Dont know anything about AFM (what is it?) Good for me to know now than later.

Unfortunately i live in Melbourne. :P, thanks for the offer though. Really appreciated that.

Where can i get those cheap spark plugs based for Nissan Skyline?

The guy told me, he sells spark plugs as well and for $5 each, but those are the shit one. He told me to get them from the Nissan dealer where it actually designs for Skyline. No need to adjust or anything, where other spark plugs i need to adjust to fix into my car. Any other opinion?

So far you guys are really helpful, even though i havent check all those poissbilty issue points and i would like to see more coming :) The more, the better :)

Regards

Charlie

might be a stupid question mate but is this happening in the wet or do you have balled tyres ?? did you know these have a traction controll that cuts all power to the coils when your wheels slip ??

underneath your steering wheel on your left there is a switch press that then go for a drive !!, i thort the same with my car it was just the tc cutting in (annoying realy )

Well maddows you are right about the traction control and thanks for pointing that out. BUT

But what you did not get was that Traction control isnt my real problem here. I know how traction control works and mine is set off always. I could drift or burn out fine.

Erm i live in Keysborough bro. If you live somewhere far from there, I would drive to see you instead since this is my problem. Here is my number. Ill text you my number in ur inbox. Its faster to communicate using phone :P

I am still waiting for more responds.

Thank guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...