Jump to content
SAU Community

Recommended Posts

A little movie of my car that i recently finished building (not done yet)

Enjoy!

Speclist:

661hp@ 1,5bar, Weight:1337kg

2,6l with a billet crank

Tomei rods

Acl pistons

Acl racebearings

Jun oilpump

Ati race harmonic crankdamper

Ported head with 264 and 272 Greddy cams,gears, buckets and valvesprings

Custom intakemanifold with 80mm tb

Modified Xs exhaust manifold

71mm Precision billet turbo

60mm wg, 2" screamer pipe

4" downpipe

4" hks race exhaust

Arc intercooler 12cm thick

75mm PPF Bov

Custom made 3" aluminum pipes

Custom made cam cover,valvecovers and coilcover

Hks 6 speed dogbox

With custom made 3-4th dogring for more durability (weak point on these boxes)

Exedy trippel plate clutch

Kaaz 2-way rear differential

6*1680cc bosch injectors (running e85)

Custom twinfeed (2* an6)fuelrail, an8 return

Aeromotive fpr

4*Bosch motorsport 044 pumps,billet fuelrails between them,1*an8 in and out

60l Rci fuelcell

Vipec v44 ecu

Custom loom

6*Vw, audi coilpacks

Custom made 60-2 triggerwheel(no CAS)

18" 10" et20 Bbs lemans with polished lips and gold painted centers

265/35 Dunlop direzza 02G

16" r32 gtr rims with 26/9,5 hoosier quicktime pro, for strip

Brembo 4pot calipers

Carbotec xp10 pads

Braided lines

No/removed Abs

Ohlins coilovers

Cusco 6 point rollcage

Cusco front camber arms

Hicas elimantor bar

No/Removed hicas system

Frp doors

Lexan doorwindows

Carbon skinned boot

Carbon hood

Nismo n1 carbon hood lip

Nismo rear spats

Stripped interior

No/removed aircon

Nismo 320 speedo

2* raceseats with 4 point harnesses

_________________

R32 Gt-r -94 661hk@ 1,5 bar

That is fcuken crazy! Love it! The roads over there are awesome! Wouldn't need to close a road or anything for a photoshoot, just do it with other cars on the road! Hahaha. On a safety note, good to see your in control (even though it is illegal) and your not someone who doesn't know what they are doing.

Way to tame a beast! More pics!!!

Thx guys!

Haha ,yeah our roads are quite decent, but we could have some off your weather here, wouldnt mine to skip the long winter of around 6-7months here

Its already ice on the roads, i live in the most southern place in Sweden..

FST513: Yes, I try to take it alittle bit easy, dont want to crash the car or someone else in the way, that would be real dogshit!

The tyres in the movie werent the dunlop tyres, i had a set of some new craptyres that we decided to burn the shit out=)

But i think i need some tyre sponsor for next year, going on alot of events and the tyres are going to have a hardlife=)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...