Jump to content
SAU Community

Recommended Posts

new pretty gate is in and new screamer made up. booked in for the tune this friday.


2013-08-31205711_zps1dcec771.jpg



routed the vac line so it goes through the heatsheild and mounted my boost solenoid (ecu has boost control in it). should help with the vac line from perishing from heat.



2013-08-31205652_zpscc1b76dc.jpg





neatly pops out here smiley.gif


2013-08-31205629_zps6fbfa06e.jpg
  • Like 1

Car is still boosting high for some reason, but now makes 351kw @20psi. If I drop it back to 18psi it sat at 345kw. But it is really happy making that power atm.

Also dropped the rev's back to 6500, and the afr's are 11 to 1 for a bit of safety

Dont mind the dip from 4700 to 6000, got a manifold leak on the last three runs from Not tight enough and cooling down over lunch.

2013-09-06133753_zpsd2a101ca.jpg

Well that didnt go as well as I hoped.


2013-09-11100548_zps3d00ddd3.jpg


Rocked up to a speed off the streets day at wakie yesterday for a bit of a test day, got 8 laps in and broke a stub axle sad.gif

Other than that the car felt excellent. The extra power and reduced weight has really change the car. Going to take a few proper laps to get used to, but the car will take any opportunity to slap me in the face if I don’t concentrate
I did manage a 1.10.10 in the lap before the axle went, which is about 1 second quicker than what i normally do in the 1st session. So i take that as a good indication im on the right track (no pun intended tongue.gif )

Also, even though tyre were cold, grip feels better too. Definitely more front and rear, was less understeery with the modified splitter. Will have to wait until I get a proper run to judge the rear.


2013-09-11083430_zpsdebec515.jpg




2013-09-11090640_zpsad2375dc.jpg




Timmies best raceface

2013-09-11092359_zps3b349b3d.jpg





bettter look at the front bar, still need to do the skirts

2013-09-11104511_zps729c115f.jpg






Im now trying to find a couple of sets of 4 stud stub axles, so if you have a spare that you want to set cheaply please PM me.
As much as i would like to, im not going to order the billet ones from the states as they will take too long to get made and sent.

ive got two sets lined up already, hopefully i'll be able to get a set in this weekend.

Only thing that worries me is why it broke.

was it because of the extra power and grip (even though not much) or was it just because it was 27 years old and stressed from the last couple of years of track work, or a combination of the two?

either way i dont see much point of pouring much more money into the rear end as it is, and so after wtac i will be putting my stag rear end in.

if you've got doubts about it, just don't do any launches and take gear changes a bit easier (ie don't power shift). Most driveline shock happens when you suddenly put power through it rather than just accelerating in gear.

easy, turn up and hand them some cash. :)

everything with 4 wheels are allowed. from street cars to race to open wheelers and karts.

thought about taking the rover out for a spin but im sure it would fall over first corner...

  • 2 weeks later...
well, i was going to try and get back to wakie today, but i forgot imy sisters uni graduation was on.
so im going to go next week.


In other news, repacement stub axles are in and i now also have a spare set. thanks james smiley.gif


These turned up too 255/40r17s soft compound (actually 265s). I'd like to thank everyone for their help it has really made a big difference to getting to wtac and my stress levels smiley.gif


2013-09-16101519_zps4f6d5515.jpg




lowered the skirts to match the front. Not the prettiest but should help stop some air getting sucked under the car. (front bar/splitter just sitting there atm)
Once again, please excuse the mess.
got some new stickers ready to go on too.

2013-09-25175131_zps16bc4cbf.jpg
  • Like 1
  • 2 weeks later...
Had a good day at the track today smiley.gif shake down and test one set of the advans

New PB 1:06.31, beating my old pb by 1.1sec yeah baby!

Both the car and I felt really good, and the grip from the advans is just insane.

20131007_100607_zpsecbe5c2a.jpg

20131007_155238_zpsac12773c.jpg


Got a bit of a boost leak too
20131007_145954_zps5856e74c.jpg



Easto was there too, but suffered a engine eating itself.
20131007_100710_zpsb4f7d885.jpg
unedited clip, so skip too 3min for the start or 7:50 for the hop lap.


http://www.youtube.com/watch?feature=player_embedded&v=rDtp493ad4s

probably 85% tyres, rest was tune, aero, and weight reduction..

has more in it too, i think a 1.05 may be on the cards next time im there. didnt want to push too hard with wtac just around the corner!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...