Jump to content
SAU Community

Recommended Posts

new pretty gate is in and new screamer made up. booked in for the tune this friday.


2013-08-31205711_zps1dcec771.jpg



routed the vac line so it goes through the heatsheild and mounted my boost solenoid (ecu has boost control in it). should help with the vac line from perishing from heat.



2013-08-31205652_zpscc1b76dc.jpg





neatly pops out here smiley.gif


2013-08-31205629_zps6fbfa06e.jpg
  • Like 1

Car is still boosting high for some reason, but now makes 351kw @20psi. If I drop it back to 18psi it sat at 345kw. But it is really happy making that power atm.

Also dropped the rev's back to 6500, and the afr's are 11 to 1 for a bit of safety

Dont mind the dip from 4700 to 6000, got a manifold leak on the last three runs from Not tight enough and cooling down over lunch.

2013-09-06133753_zpsd2a101ca.jpg

Well that didnt go as well as I hoped.


2013-09-11100548_zps3d00ddd3.jpg


Rocked up to a speed off the streets day at wakie yesterday for a bit of a test day, got 8 laps in and broke a stub axle sad.gif

Other than that the car felt excellent. The extra power and reduced weight has really change the car. Going to take a few proper laps to get used to, but the car will take any opportunity to slap me in the face if I don’t concentrate
I did manage a 1.10.10 in the lap before the axle went, which is about 1 second quicker than what i normally do in the 1st session. So i take that as a good indication im on the right track (no pun intended tongue.gif )

Also, even though tyre were cold, grip feels better too. Definitely more front and rear, was less understeery with the modified splitter. Will have to wait until I get a proper run to judge the rear.


2013-09-11083430_zpsdebec515.jpg




2013-09-11090640_zpsad2375dc.jpg




Timmies best raceface

2013-09-11092359_zps3b349b3d.jpg





bettter look at the front bar, still need to do the skirts

2013-09-11104511_zps729c115f.jpg






Im now trying to find a couple of sets of 4 stud stub axles, so if you have a spare that you want to set cheaply please PM me.
As much as i would like to, im not going to order the billet ones from the states as they will take too long to get made and sent.

ive got two sets lined up already, hopefully i'll be able to get a set in this weekend.

Only thing that worries me is why it broke.

was it because of the extra power and grip (even though not much) or was it just because it was 27 years old and stressed from the last couple of years of track work, or a combination of the two?

either way i dont see much point of pouring much more money into the rear end as it is, and so after wtac i will be putting my stag rear end in.

if you've got doubts about it, just don't do any launches and take gear changes a bit easier (ie don't power shift). Most driveline shock happens when you suddenly put power through it rather than just accelerating in gear.

easy, turn up and hand them some cash. :)

everything with 4 wheels are allowed. from street cars to race to open wheelers and karts.

thought about taking the rover out for a spin but im sure it would fall over first corner...

  • 2 weeks later...
well, i was going to try and get back to wakie today, but i forgot imy sisters uni graduation was on.
so im going to go next week.


In other news, repacement stub axles are in and i now also have a spare set. thanks james smiley.gif


These turned up too 255/40r17s soft compound (actually 265s). I'd like to thank everyone for their help it has really made a big difference to getting to wtac and my stress levels smiley.gif


2013-09-16101519_zps4f6d5515.jpg




lowered the skirts to match the front. Not the prettiest but should help stop some air getting sucked under the car. (front bar/splitter just sitting there atm)
Once again, please excuse the mess.
got some new stickers ready to go on too.

2013-09-25175131_zps16bc4cbf.jpg
  • Like 1
  • 2 weeks later...
Had a good day at the track today smiley.gif shake down and test one set of the advans

New PB 1:06.31, beating my old pb by 1.1sec yeah baby!

Both the car and I felt really good, and the grip from the advans is just insane.

20131007_100607_zpsecbe5c2a.jpg

20131007_155238_zpsac12773c.jpg


Got a bit of a boost leak too
20131007_145954_zps5856e74c.jpg



Easto was there too, but suffered a engine eating itself.
20131007_100710_zpsb4f7d885.jpg
unedited clip, so skip too 3min for the start or 7:50 for the hop lap.


http://www.youtube.com/watch?feature=player_embedded&v=rDtp493ad4s

probably 85% tyres, rest was tune, aero, and weight reduction..

has more in it too, i think a 1.05 may be on the cards next time im there. didnt want to push too hard with wtac just around the corner!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
    • Well, yeah. But I just expect everything other than my car to feel like a bucket of shit anyway. I still miss my Alfa 116 so much though. You could run over a 20c piece and tell whether it was heads or tails.
×
×
  • Create New...