Jump to content
SAU Community

Recommended Posts

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

No he does, really he does drive like, well like you should be, just follows a bit close, but it is a very easy mistake to make, most of the time I could not see his headlights in my rear veiw mirror, asked him not to follow so close, and he didnt for a while but still crept up a bit after a while, didnt really bother me as I then made sure that I kep a big gap in between me and MJ so that I did not have to brake in a hurry and expect him implanted in my boot :D

Didnt once want to race or leave any rubber anywhere.

Hweres some pics of some of the girls i know back home in sydney ..

There not that good looking, but its the only pics i had of some hicks i knew, When i go back home in a few weeks ill try and round up all the hot ones and get some photos for you

the 2nd pic is a photo of my ex girlfriend .. ****in bitch .. shes the reason why i hate women more then ska :D

Hweres some pics of some of the girls i know back home in sydney ..

There not that good looking, but its the only pics i had of some hicks i knew, When i go back home in a few weeks ill try and round up all the hot ones and get some photos for you

the 2nd pic is a photo of my ex girlfriend .. ****in bitch .. shes the reason why i hate women more then ska :D

the first gal was just on your bed letting you take a pic of her?? wat's the trade off ?? :D

you going back hom to Syd permanently?

Nex - well im goin to stay up to see them .. and if they aint good enough ill be pist off as i have an early start tommorow, and have to be up in the valley or somewhere in briz at like 9 am :S

Genesis - nah she was just laying on her bed while i was in her shower .. i got out and grabbed the camera :D

I wish iw as going back home permantly ... but sadly its just to visit

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...