Jump to content
SAU Community

Recommended Posts

I just picked up my R32 GTR from its quarantine inspection and when I revved the vehicle to about 6K rpm's suddenly heaps of thick smoke began pouring from the exhaust. It seems that the smoke was only generated when the car was in gear as it would thin out when in neutral.

When I stopped the vehicle it wouldn't start again. The engine would turn over but not fire up.

Has anyone experienced similar problems? I have been told it might be a blown oil seal in the turbo.

Any help would be appreciated

Link to comment
https://www.sau.com.au/forums/topic/34355-thick-smoke-pouring-from-exhaust/
Share on other sites

A blown turbo seal would not prevent the car from starting. What colour was the exhaust smoke? The head gasket couldve blown and filled with coolant (the organic head gaskets Nissan put on from the factory are quite worn out after 15 years of hard driving) or you couldve done some more serious internal damage. I assume this is a 15 year old import? If so keep in mind the car would have sat on the docks for quite some time (several months), the fuel would have gone stale and combined with our high temperatures, its not a good combination.

Id take it to a reputable mechanic and get a compression and leak down test and go from there.

A leak down test is similar to a compression test, but instead of telling you how much pressure is in a cylinder, it tells you how much pressure is leaking from a cylinder. Any more than around 25 - 30% leakage is a big problem.

pressure test the cooling system, take plugs out while system is under pressure and crank the motor, if water sprays out....bad news(headgasket). There is also a sniffer they can put over ur radiator filler neck and if it detects and exhaust gases then the dye in the sniffer changes colour, ours goes greeny yellow from the original blue colour. also water in oil and oil in water.

plz don't double post your problem godzillr

also water in oil and oil in water.

1st thing to check..

Id take it to a reputable mechanic and get a compression and leak down test and go from there.

:werd: = worse case scenario. However may just be bad petrol, or due to it sitting there for months with "stale" oil, or a multitude of less serious problems.

If it is an 1989 car, I hope yours is an exception and not going to the common place when 15 year GTR's start flooding the country until the government changes the laws. Feel sorry for you if its serious damage, as a rebuild on RB26DETT is well into the 1000's and you have a lemon.

Everything seems to be intact.

I have just taken it to Skyline Performance Imports in Canberra. Unfortunately they won't be able to have a good look until mid next week. It is looking like it could be expensive.

When I find out what the problem is I will let everyone know.

Everything seems to be intact.  

I have just taken it to Skyline Performance Imports in Canberra.  Unfortunately they won't be able to have a good look until mid next week.  It is looking like it could be expensive.  

When I find out what the problem is I will let everyone know.

Godzillr - let me know how it goes, as I got my R last week and it is looking pretty good. did you hear any loud/bad noises when you reved to 6k?, did it rev cleanly or stutter and fluff? how much fuel did you hav in the car???

good luck with it, look forward to catching up with you.

Danooh- I will certainly let you know and congratulations on your car...

I didn't hear any noises but it did misfire between 5K and 6K rpm's. I picked up the car and it was completely out of fuel. I filled it to the top with BP premium. I drove it for a good 60km's before I had the problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...