Jump to content
SAU Community

Recommended Posts

Speaking from the Cressida experience, set no.1 piston to top-dead-centre lining up markers on the cam gears making sure it was for the compression cycle, think i needed the cam covers off to check it was, then had to line up a marker on the dizzy to a mark on the block and that basicly got it all lined up. Not sure how nissan engines are set up though, best bet is a workshop manual on how to set timing.

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

^^ sounds like this may be the drama...

i think lining up the red marker on the harmonic balancer (0 degrees) with the mark on the lower timing belt cover is TDC...

take the cas off while i do this. then line it back up once its at TDC?

Here is SKs article again:

http://www.skylinesaustralia.com/forums/Ca...m-B-t73824.html

If you are not absolutely confident that you have the timing correct than please take it to a competent workshop if there is one in your city - you don't want to redo all the last few weeks' work.

Yes the fuel lines will hold alot of pressure even when the car is off, there are check valves that do this so there is pressure at the injectors next time you start the car. I'll take a pics of my fuel lines when I get home this arvo, I'm running the stock setup.

It won't be the ignition timing if, all the cam gear and crank pulley marks lined up when you put the timing belt on, and the cas was installed correctly. Even if your cas is in the wrong position, retarded or advanced, the engine will still start. I wouldn't worry about the firing sequence as the NEO's coils and coilpack loom only fit in one way, it would be hard to mix them up.

The fuel injectors don't fire directly into the cylinder, they fire into the intake valve camber, so as long as the injectors fire, the fuel will get into the cylinder. it has nothing really to do with the exhaust cam and valves. An easy way to test the injectors and coils are firing is to remove the CAS, leave it plugged in, switch the ignition to "ON", and spin the CAS by hand, you will easily here the injectors tick and coils fire.

The nistune maps will be stock, but have you tested the ecu works? And are you running the stock AFM and injectors?

Edited by QWK32
remove the CAS, leave it plugged in, switch the ignition to "ON", and spin the CAS by hand, you will easily here the injectors tick and coils fire.

Very good point.

The nistune maps will be stock, but have you tested the ecu works? And are you running the stock AFM and injectors?

At the moment to get it running he has got stock injectors and AFM yes, once its running they are coming out and bigger cc and z32 before its towed to tuner. Dont believe the ECU has been tested to check if it works or not.

If the fuel pump is working, and it does, and the fuel is going nowhere caus it spupts out, would this not indicate a problem with the fuel relief valve.???. Check and make sure none of your boost/vacuum lines are split or pinched off with say a zip tie.

I had a guy with a laptop check mine over last week, cost $80 at home. AFM, A/F ratio, spark, timing, injectors all checked out OK. I still have a prob somewhere but at least I know what is NOT wrong.

The fuel pumps fine...

Ill give this injector and coil test a crack...

If the fuel pump is working, and it does, and the fuel is going nowhere caus it spupts out, would this not indicate a problem with the fuel relief valve.???. Check and make sure none of your boost/vacuum lines are split or pinched off with say a zip tie.

I had a guy with a laptop check mine over last week, cost $80 at home. AFM, A/F ratio, spark, timing, injectors all checked out OK. I still have a prob somewhere but at least I know what is NOT wrong.

So might pay to rip the cam

Cover off and have a look... The 2 cam poimts will b lined up if the cranks on the red (0 degrees) marker yeah?? This will tell me if im a tooth out and if inj and coils are working at same time.

The ecu is my old 1 chipped. Unlikely its the issue but maybe worh ruleingout

The fuel pumps fine...

Ill give this injector and coil test a crack...

So might pay to rip the cam

Cover off and have a look... The 2 cam poimts will b lined up if the cranks on the red (0 degrees) marker yeah?? This will tell me if im a tooth out and if inj and coils are working at same time.

The ecu is my old 1 chipped. Unlikely its the issue but maybe worh ruleingout

yeah, the cam marks will line up once every 2 turn of the crank. i.e 1 cam rotation = 2 crank rotations. don't worry about the markings on the belt, they only line up sometimes.

i also agree that its unlikely the ecu, its just an idea that as you say would be worth ruling out. i only mentioned it as i was thinking along the lines of the base image/map not being saved to the board after nistune was installed. probably very unlikely as anyone installing it would have checked it was all ok before giving it back to you.

removing the cas and spinning it manually will give you a good idea if the ecu is working anyway. if the injectors and coils fire then you know the ecu is getting the CAS signal processing it and telling them to fire.

Replace injectors,afm then tow that peice of shit to turbotune and get mike to figure it out

Ps- is Adam your mate chris?

lol blow me...

seems my fuel lines are round the wrong way :D .... will report back :)

so the car started... had a very big fuel leak at the rear injector,

.... gota take em out and have a play... im guessing just an o-ring drama... :P

y cant the rail be as easy to get to as an rb26 :P

lol blow me...

seems my fuel lines are round the wrong way :P .... will report back :P

Was looking at that last night. WTF!!! Looked at the pics and thought "no one could do that, except me"

My fuel lines are actually arse about. Fuel comes in at the back and unloads at the front. This is a mod that was done with FFP.

Hope you are getting sorted.

ok so the cars running....

seems to be pretty good apart from a few things...

how much coolant should it take? i would no have around 9-10L in it i rekn

ive filled it up on level ground, ran it whit bleed nipple (manifold) off, and a funnel with a fair bit in it.

how ever it doesnt seem to want to come out the bleed nipple unless its turned off/turning off....

i can squeeze the thermostat hose and it will shoot up a little bit, but its only once its off that it shoots out as if it should...??

also the turbo wheel sounds to be spinning down once the cars turned off... its a hks 2535 and ive never ran it b4... it only does it once it starts to get a bit of heat into it (no where nere running temp) but still too warm to touch.

also the turbo wheel sounds to be spinning down once the cars turned off... its a hks 2535 and ive never ran it b4... it only does it once it starts to get a bit of heat into it (no where nere running temp) but still too warm to touch.

Typical of a ball bearing turbo. They spin alot more freely over bush ones

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...