Jump to content
SAU Community

Recommended Posts

I have the following rb20det parts for sale;

- rb20det/rb25det Cometic triple layer stainless exhaust manifold gasket $80ono

- Rb20det crank rods and pistons in good usable condition offers...

- rb20det red top injectors 240cc good upgrade for non turbo rb20 suitable replacement for rb20det $60

- inlet plenum rb20det top halfs x4

- inlet plenum rb20det

- rb20det gts4/gtst bonnent holder good condition $40

- gts4 diff half shafts 2 sets offers

- rb20det cam angle sensor CAS $80

- rb20det throttle body and tps throttle position sensor $60

- rb20det knock sensors x6 20 each

- ignitor module offers

- rb20det sump gtst x3 offers

- rb20det oil pickup x3

- coil packs x6 $120 ono 80ks gts4 later model ones much stronger have a coiled spring and no lead inductor same plug all lines up with any rb20det etc

- r32 wiper bottle tank with twin pumps factory in good condition no cracks or scale 100ono hard to find in good condition

and plenty more i cant think of trade and/or cash for q45 or z32 afm with plug rb26 ballast resistor pack rb25det stainless front facing plenum rb25det series 2 ecu and loom adjustable cam gears always keen to do deals.

cheers

Lagperformance

0450 728 189

Link to comment
https://www.sau.com.au/forums/topic/344080-rb20det-parts/
Share on other sites

  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...