Jump to content
SAU Community

Recommended Posts

Hey everyone my 32, currently unregoed but its not defected or anything, can get walk in rego.

Car: Black 2 door r32 gtst, 1990

Km: 82,XXX

Mods and info:

Rb20DET engine

5 speed trans

Extreme Cushioned Button Clutch, Replaced about 5,000kms ago

VG30 High flow turbo, Runs standard Boost (10Psi)

3 Inch Trust Exhaust, one muffler at the rear. No Cat, Comes with High Flow Cat, can put in at buyers request

K & N Pod filter

Large Front Mount Intercooler with stainless steel piping

LSD, unsure on what sort

GREDDY coilovers all round, 32 way adjustable damper, also height adjustable. Handles Real nice (comes with standard suspension all round as spares)

Front and Rear Strut Braces

Advan Super Wheels 16" red and black

Boost Guage

Apexi Turbo Timer

Alpine Head Unit, Descent Speakers i think also alpines.

Sub and Amp in the boot, Sub mounted to rear strut brace, amp needs mounting

Remote Central Locking/Alarm system, Remote needs a new caseing but still works

Have had the car for about 14 months now with no major dramas, only thing that went was a clutch a few weeks after i got it.

it got defected in December last year for being too low (was only by about 15mm).

but i got it off defect reasonably easy, just changed the struts around and quietened the exhuast and put a cat in it. and it passed first go. when i took it through i also had rocker cover gaskets done and speedo drive seal and steering rack boots. The car is very clean underneath.

It drives nicely, Goes pretty hard for an rb20.

Has a small dent above the Right hand rear wheel arch.

Would like to get rid of my debt which is my reason for selling.

Price: $8.5k ono. Will consider Swaps but mainly would like cash.

Contact: Alex, 0403 279 862, cheers

Pics:

post-a296014-IMG-7912.JPG

post-a285604-IMG-7927.jpgpost-a285605-IMG-7931.jpgpost-a285606-IMG-7935.jpgpost-a285607-IMG-7936.jpgpost-a285608-IMG-7939.jpg

Edited by WrenchesInTheGears
Link to comment
https://www.sau.com.au/forums/topic/344390-r32-gtst-for-sale-85k-ono/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...