Jump to content
SAU Community

Recommended Posts

ever wondered what the small round plastic thing is at the far left side of the front windscreen demister is?

it's a sun load sensor for the climate control. when you hit econ instead of A/C it measures the direct sunlight and works hard when needed rather than just all the time.

Heater or A/C not working well?

Climate Control Diagnostics

if you turn your ignition on and then hold the off button on the climate control for 5 seconds you will enter diagnostic mode.

hit the temp increase button (red triangle) to test all sensors. if any sensor is giving wrong readings it will give you a code.

20 means nothing is wrong and 21 through to 27 will give you the sensor that is faulty.

keep in mind, you must have direct sunlight on the sun load sensor for it to diagnose properly (otherwise it assumes the sun load sensor is stuffed)

20 - all is normal

21 - outside air sensor

22 - Inside air sensor

23 - Water temperature sensor

24 - Intake temperature sensor

25 - Sunload sensor (small sensor on the left hand side of the dashboard near the windscreen)

26 - PBR

27 - Refrigerant temperature sensor

ever wanted the climate control to try harder to cool or heat?

to enter full cold mode, turn the temp down to 18 degrees then hold the cold button. (figured this out accidentally)

do the same for full heat but turn it up to 32 then hold the hot button.

ever wondered where the climate control takes the interior temp reading from?

just right of the ash tray there are little slots in the plastic. that's where.

whilst moving if you turn the ignition off and on you lose all wheel drive until you stop.(fairly well known but maybe you didn't know)

any more cool stuff, please let me know! i love finding these things out!

  • 1 month later...

Thanks for this. Very interesting. Bloody 1990 cars shoulda been make in 1997 or something lol.

Can this sort the problem of not being able to increase temp? Soemthimes I can only decrease temp and not increase (when I press the red arrow it does nothing).

Edited by TyresBro
  • 5 months later...

Thanks for this. Very interesting. Bloody 1990 cars shoulda been make in 1997 or something lol.

Can this sort the problem of not being able to increase temp? Soemthimes I can only decrease temp and not increase (when I press the red arrow it does nothing).

Just going through a few old replies I never read, this sounds more like a stuffed hot button on your climate control unit. I'd buy a second hand unit or take it to a small electronics store :) you often find one little old guy that owns it and will help with anything electronic. They'd be the two things I'd conceder anyway. Seen r32 climate control units on eBay for $200.

  • 4 months later...

Hey mate, I've got 2 climate controls, both work fine fast heat fast cold up down ect, my heater was stuck on and heater tap wasn't moving on FC so I changed it now it does, however it's still stuck on hot air when I change the heat up and down and the tap isn't moving, I think it's a sensor somewhere but neither of the units will go into diagnostic mode, any ideas anyone? Help will be appreciated cheers!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...