Jump to content
SAU Community

Racing Tips Needed

Johny Bravo

By Johny Bravo,
in Motorsport Discussion & Builds

 Share

Recommended Posts

Snowman Grand Master

Snowman

Posted
Posted
So what should i do in wet conditions?

Slow down a little :(

Also at the track in the wet it often has more grip OFF of the racing line. (especially under brakes - brake more towards the in-side line if that makes sense).

LSX-438 Mentor

LSX-438

Posted
Posted

The biggest mistake i see BY FAR for people new to the track is.. they just go for it straight up, with no warm up. I must have organised countless track days myself, and you can bet your bottom dollar after the first session, a good ratio of the newbies have cooked their brakes, blown diffs etc. Too much enthuse!

toffy Veteran

toffy

Posted
Posted

if it's wet at basky put your tyres up to about 50psi , if it's dry start with 38 in the front and 34 in the rear. Auto would be difficult around there , be prepared fro the skyline (the corner at the top of the hill) you can't see it 'till your on it , enjoy :( oh p.s expect to scrub your tyres heaps and your r31? does it have std brakes? they will die quickly as soon as you start driving it hard . kamikaze croall will be able to help you out heaps ;)

Johny Bravo Proficient

Johny Bravo

Posted
  • Author
Posted

sorry fulla's only got her back yesterday and haven't been to the track yet, brakes seem stiffer then i remember so thats something i gotta tackle first. for those of you who haven't seen it yet, find my thread "STS Turbo Setup" in forced induction. Oh wait, here's the link, forgot i could do that: http://www.skylinesaustralia.com/forums/topic/340173-sts-turbo-setup/

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...