Jump to content
SAU Community

Recommended Posts

would u be concerned if it was higher than ur last? :)

there have been a couple of people from this forum who have dynoed there cars on other dynos like BMT and the ones the guys from ICE use and then without any changes had them dynoed on the AVO pulleys with about a 10kw+ difference...

nothing major...

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

hahahaha dont listen to them mupkant, buy a killer handling setup and kick some ass when you get to round-a-bouts and other such turns (of course, ones that are on your own private test tracks, you know....)

hahahaha dont listen to them mupkant, buy a killer handling setup and kick some ass when you get to round-a-bouts and other such turns (of course, ones that are on your own private test tracks, you know....)

i have nightmares about roundabouts, while back ago

sorta speed through a round a bout during wet road...and

lets just say i got really close to saying hello to the 'keep left' sign.

I aint implying anything. Its just that they use a dyno around the corner from their place if they are only running 1 car, so they dont have to drive all the way to bayswater and back and waste half a day. Plus with those minimal mods u can get false readings unless u go to joe blogs backyard dyno and reel off 200rwkw after the secret mods joe blogs has done on your car ;)

I aint implying anything. Its just that they use a dyno around the corner from their place if they are only running 1 car, so they dont have to drive all the way to bayswater and back and waste half a day. Plus with those minimal mods u can get false readings unless u go to joe blogs backyard dyno and reel off 200rwkw after the secret mods joe blogs has done on your car ;)

hehe lol

why did you have to crush my hopes of my car giving good performance ;)

maybe a 1/4 time should really show its real power?

oh btw its 95 model, so im suppose to have that freak ecu? heh.

The purple graph seems to be running preety straight 12 a/f ratio which took abit of tuning on my power fc to get on my tune. The stock ecu would be down in the 10 amd 9 a/f ratio on boost.

Your car was dynoed at the place around the corner from ice, MK as the dyno graph shows. It apparently has the same dyno as racepace.

Those numbers seem pretty right, i got a peak of 178rwkw at Race Pace, running at least 12psi, before dropping off to 10psi. I only had SAFC, exhaust, standard air-box and bleed.

I personally witnessed it.

Though, i beleive all dynos have a descrepancy, could be minimal, but most do.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...