Jump to content
SAU Community

Recommended Posts

I have recently purchased a r32 skyline gts. i had been driving it around perfectly fine for a couple of days then out of no where, the power windows and all the gages and warning lights except for the speedo stopped working. the engine still runs fine and the car drives without problems. anyone know what may have cause this?

thanks for the help

Link to comment
https://www.sau.com.au/forums/topic/348008-electrical-problems/
Share on other sites

The speedo will work because it's mechanical.

Do the warning lights come on when you put the key to "ON", ie just before you start the engine? Any other symptoms you can tell us about?

Maybe check the fuses with a multimeter - often the fuse can look perfectly ok but have the smallest of breaks in the fuse material.

The fuses have two metal points on each end. Earth a test light and test both points of the fuse make sure all the dash/accessories/power window fuses work.

If you've got an aftermarket stereo, there is a slim chance the wires could be melted or somethings gone wrong. Ive seen a ford laser have its wires melted together because the draw of the headunit was too much for the wiring in the car. Caused alot of electrical issues..

  • 3 months later...

Car batteries are much better today than they were even a few years ago. I've had batteries last as long as 9 years in a car, which is amazing. Only a few years back, the "60 month" DieHard car battery from Sears was considered the top of the line. Technology has improved over time.But car batteries can fail at any time, even when brand new. And although they can last as long as 9 years, typically most fail in the 5-7 year range, if not before. And cheaper batteries might not last even that long.The failure mode of car batteries appears sudden, which is something that confuses people. Most folks' experience with batteries is based on flashlight or other consumer product batteries. A flashlight battery fails slowly over time, getting dimmer and dimmer, until one day, it is a mere flicker and then goes out. Consumers think that this gradual failure mode applies to car batteries as well, which is why they dismiss the battery as the problem when the car "suddenly" fails to start. bmw tail lights

Edited by jazmin
  • 8 months later...

anyone have any ideas?

my car has just randomly done the same thing except in a 32 gtr.

no dash warning lights when you turn the key to on, the front torque gauge goes all the way up to max, no power windows etc and there is a relay in the boot that keeps ticking every 30 seconds?

start the car and using a multimeter check if the alternator is charging. i have come across a number of cars that cause failure to dash and power windows etc. when there is a fault with the alternator. it could be the alternator itself or even a broken wire going to the alternator.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Input shaft bearing. They all do it. There is always rollover noise in Nissan boxes - particularly the big box. Don't worry about it unless it gets really growly.
    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
×
×
  • Create New...