Jump to content
SAU Community

Recommended Posts

Been a bit slow in this thread lately... so thought I'd stick up some pic's of the hydro handbrake I have been making after work this week. It's pretty much ready to bolt in and plumb up now.

Bits fresh out the mill ready for welding:

5260050683_e171f696da_b.jpg

Test fitting in my track 180 after welding:

5265473535_9024ca210e_b.jpg

Pivot base installed:

5268433582_0b5d12cda6_b.jpg

After glass beading and the adjustment lock nut turned up and installed:

5273052733_7590092963_b.jpg

The guts of it:

5273661338_0f7cb4a38f_b.jpg

Edited by samstain
Link to comment
https://www.sau.com.au/forums/topic/348019-vertical-hydro-handbrake/
Share on other sites

  • 1 month later...

thats nice, scuse my ignorance, but do you then run the cable from the hand break forward instead and it pulls on the pivot rod?

this is the exact reason why I'm trying to convince my boss that HE needs a 3 axis mill........ So I can come in on weekends and play.

thats nice, scuse my ignorance, but do you then run the cable from the hand break forward instead and it pulls on the pivot rod?

this is the exact reason why I'm trying to convince my boss that HE needs a 3 axis mill........ So I can come in on weekends and play.

Hydraulic hand brakes dont use cables, the use the hydraulic brake lines, route then through a speceific master cylinder and the rear brakes are worked normally when the lever isnt used and when the lever is used it only works the rear brakes.

5265473535_9024ca210e_b.jpg

Im assuming from how it is mounted above and looking at the pic below that the upright in the pic below will have an extension slipped over it and/or bolted to it and the stick will come up through the hole where the stereo and pocket use to be, im also guessing that it will be bent in some way so the knob will be further back towards the driver.

All of this is just my assumption, would love to see finished pics.

5268433582_0b5d12cda6_b.jpg

yeah brett's right, the old handbrake will be ripped out, a handle custom handle slips on so the new mechansim and is screwed in to place (you can just see one of the holes in the last photo).

Photo 3 & 4 shows it without and with the handle.

The handle is just a bit of tube, so once the base is mounted I'll cut it to length and bend it if requried to get it in to a comfortable position.

  • 2 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...