Jump to content
SAU Community

Recommended Posts

can anyone help me i have just put a S2 engine into my S1 33 skyline and im trying to get it started it will turn over but will not fire it has no spark what could my problem bee what shoild i do to get this sorted????

Take the Cam Angle Sensor off, leave it connected to the loom and slowly turn the gear around, listen for the injectors clicking away happily, or not so happily. If they are opening and closing, take a plug out, and leave in in it's coil pack, rest it on the block so you can see the gap, and turn the lights out and slowly turn the CAS gear over, you should see a spark, be careful tho, that can give you a belt if you are holding onto it while rotating the CAS.

Both of the above require the igniton on, tell us how you go.

If you're attempting to use the S1 loom/computer with the S2 coil packs, the ignitor setup is all different.

Ignitor on S1 is the item that sits up the back.

On the S2 it is built into each coil pack.

Going through the same thing but i havent put the engine in yet though, im using S1 loom, S1 coils and igniter but im going to see the result with S2 TPS and CAS, if i have to get these too or not.

im also thinking you've mixed up s1 and s2 ignition parts. either use s1 coil packs and ignitor pack or just the s2 coil packs (not sure if you need to use the s2 ecu if you're using the s2 coil packs though).

ive installed a s2 engine using all of my s1 accessories - works perfectly fine. the only issue you'll have with the s2 throttle body is the loom plug - you'll have to check if the s1 fits as it has 2 plugs coming off the TPS. the series 1 and 2 CAS's are interchangeable.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...