Jump to content
SAU Community

Recommended Posts

IMO the officer is in the wrong and cannot specify which VicRoads you need to attend as any defect can be cleared at ANY VicRoads.

You would be wrong here, an officer can tell you what vicroads to get it cleared at. If they want to make life hard, they could have put Mildura.

In most cases they right ANY (vicroads) in this section, but nothing stops them from put a certain vicroads.

If they have put on there VASS required, Vicroads wont clear the defect until you get the certificate. The VASS engineers might be picky with other mods you have.

Your correct, if a VASS is stated as required then you need one. it won't be cleared without it.

And yes an officer can require one on a defect notice.

i know cops have the authority to defect a car based on an observation of unroadworthiness and the right to report you to the EPA based on an observation of the car being below emmisions standards .... but i wonder if they have the right to order a vass engineers certificate!

Yes they do.

So the police. As stupid as some can be are qualified to ask you to get a vass certificate? That's f**ked up. Before any cop does a check on your car ask them if they have completed the according training and have the certificate with then that they can do a rwc check. Has caught out a few cops in my time :) they cbf calling tmu so I left.

Cops don't need to do any training to issue defects, as soon as they are cops they can.

No one carry's the certificate, as its not required and anyway as its an A4 sheet of paper, so its not that easy to carry :rolleyes:

ive been scouring the net through all the traffic laws, acts etc. i cant find anything solid about police and vass, do you know where i can find it?

here for VASS

http://www.vicroads....atoryScheme.htm

and

http://www.vicroads....difications.htm

and

http://www.vicroads....8340/0/VSI8.pdf

Edited by tss

ive been scouring the net through all the traffic laws, acts etc. i cant find anything solid about police and vass, do you know where i can find it?

And for the police bit

here

http://www.austlii.e...986125/s14.html

*PS sorry about the number of post, I was replying as I was reading

Edited by tss

i can see the defect bit, and the conditions of use of the vehicle part, what about the right to request a vass certificate

Here it is, under Road Safety (Vehicles) Regulations 2009 section 257 http://www.austlii.e...09309/s257.html

257 Use of modified vehicles

(1) A person must not use on a highway a vehicle that has been modified from the condition in which it

was in when first registered unless the modification—

(a) has the Corporation's approval; or

(b) has been carried out in accordance with guidelines published by the Corporation

which are available—

(i) at the offices of the Corporation; or (ii) on the internet website of the

Corporation.

Penalty: 5 penalty units.

(2) The Corporation must not give its approval to or in respect of a vehicle modification if the vehicle no longer complies with the standards for registration unless the Corporation proposes to register the vehicle under regulation 30(1).

The Corporation approval means a VASS certificate

Guideline published by the corporation means VSI (vehicle standards information)

I can't prove this more then this, without releasing internal documents which I not allowwed to do.

But trust me, I do this for a living, I'm giving you the correct information, I have no reason to lie to you. If you really want to check call the the police general number and ask to speak to the Vehicle safety testing centre and ask them.

You own me a beer sometime for digging this stuff up.:thumbsup: as I'm doing it on my own time to help you.

And yes the cop may be was a bit tough on you, bit you did know that you were breaking the law. as it's said "do the crime, do the time"

i believe you mate i was just after something written in regards to vass i couldnt find anything

Yeah no problems, I'm happy to help if I can.

The information I posted was from the Victorian police Vehicle Safety Manual, but I can't post it up.

I know it doesn't spell it out in laymans terms but thats is where it relates.

What the cop has done is right, maybe a little harsh? I can't say as I wasn't there! but what he has done is not outside his powers.

Edited by tss

Yeah no problems, I'm happy to help if I can.

The information I posted was from the Victorian police Vehicle Safety Manual, but I can't post it up.

I know it doesn't spell it out in laymans terms but thats is where it relates.

What the cop has done is right, maybe a little harsh? I can't say as I wasn't there! but what he has done is not outside his powers.

sounds to me like you're a cop :O

Quick everyone, hide your mods!!1 :P

(welcome :) )

far, far, far worst then that,:whistling: I've been outed earlier, look it up.

oo i see.

Well if you cant beat them, join them? Welcome to SAU :P

haha, depends what you mean by worse. I find powertripping cops much worse as they try to ping you with nonsense, whereas you have your facts straight and you cant argue with the facts

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
×
×
  • Create New...