Jump to content
SAU Community

Recommended Posts

he is aiming for 380kw though, certainly not low, but not some 500kw monster that needs it to get the power.

Its easy to become indifferent to numbers but 380 wheel watts is a friggin lot of power.

Do A nicely balanced head to suit and it will make that power more efficiently with better boost and torque characteristics too.

Thanks for the feed back so far gents..

Its good to see other peoples opinions on head work re the RB..

380rwkw was just a figure I pulled from the sky, I use to drive it at 300kw so I was merely adding a reasonable factor on top.. Hell the more power I can screw out of her the better.. But in reality I want to make sure I do everything right. Keeping in mind I'm still retaining the purist RB25 standard capacity approach..

As for 5K worth of slicks, well I'm sure that could occur but far far later down the track as well its still in bits/undrivable at this point in time..

Now another question, I have heard that the bronze guides have a pretty quick wear rate?? If this being true is there any other guides in which I can use?? Keeping in mind I want to use the 1mm oversize valves..

Cheers..

Thanks for the feed back so far gents..

Its good to see other peoples opinions on head work re the RB..

380rwkw was just a figure I pulled from the sky, I use to drive it at 300kw so I was merely adding a reasonable factor on top.. Hell the more power I can screw out of her the better.. But in reality I want to make sure I do everything right. Keeping in mind I'm still retaining the purist RB25 standard capacity approach..

As for 5K worth of slicks, well I'm sure that could occur but far far later down the track as well its still in bits/undrivable at this point in time..

Now another question, I have heard that the bronze guides have a pretty quick wear rate?? If this being true is there any other guides in which I can use?? Keeping in mind I want to use the 1mm oversize valves..

Cheers..

I'll say this quietly in case Nismoid is listening.

Use the factory iron guides, they are more durable than the bronze jobbys.

Getting the engines breathing characteristics to suit the other mods is the key to unleashing the true potential of your build.

Every performance category be it, drags, marine, Tractor pulls, circuit,N/A Forced induction or whatever has had countless hours of time and money poured in to developing cylinder heads simply because that is where Real horsepower benefits and torque characteristics to suit the application can be found.

Mismatching parts, and not understanding the application is where things seem to come unstuck.

Best example I've seen many times over is using drag spec engine+head mods in ski boat engines. Different discipline, different requirements, need different parts and approaches to specs and modifications.

Have you considered swapping the motor or maybe head to a neo rb25det

Head has soild lifters, larger exhaust valves already

Not sure if the stock neo head will make your power goal, but with researching.

May work out alot cheaper

Have you considered swapping the motor or maybe head to a neo rb25det

Head has soild lifters, larger exhaust valves already

Not sure if the stock neo head will make your power goal, but with researching.

May work out alot cheaper

+1 If you can find one to start with.

Question..

What supertech cam followers do I need to purchase if I choose to use the Tomei 270/10.25mm cams??

I've been told there are 29mm and 31mm base circle styles..

Cheers..

Hi,

Looking for some help with cams... I've just bolted up a GT3076 with internal gate to my RB25 series 1 and I have a pair of Tomei Poncams 256 degree 8.5mm lift I would like to drop in. I'm not looking to get any real power gains from them, but just to move the powerband round, for more response and and earlier spool up, would these cams be adequate for the job? The cams came with the option VCT retained, what is this about and is there any tutorials or DIY's on instalment of these cams?

NISSAN SKYLINE R33 GTS-T series 1 RB25det

Garrett GT 3076

CHRA(CORE)

700177-5007

COMPRESSOR HOUSING

436157-0023 (SURGE SLOTTED)

COMPRESSOR HOUSING AIR RATIO

0.60

COMPRESSOR WHEEL INDUCER SIZE (MM)

57.00

COMPRESSOR WHEEL TRIM

56

18 PSI ACTUATOR

-Apexi Power FC

-Apexi AVC-R

-Nismo 740cc injectors

-Z32 AFM

-Walbro Intake fuel pump 255l/hr 500hp rated

-Tomei Poncam intake and exhaust 256 degree 8.5mm lift

-Super Spark coilpacks

-NGK Laser Platinum PFR5G-11

-Apexi Power intake

-3' Exhaust turbo back

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...